Yamaha FZ-6 FZS6C Owner'S Manual Download Page 83

Page: 83 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-41

5. While supporting the brake caliper

and slightly lifting the wheel, pull
the wheel axle out.

NOTE:

A rubber mallet may be useful to tap the
wheel axle out.

6. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

NOTE:

The drive chain does not need to be
disassembled in order to remove and
install the rear wheel.

7. Remove the wheel.

CAUTION:

ECA11070

Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.

EAU32941

To install the rear wheel

1. Install the wheel and the brake cal-

iper bracket by inserting the wheel
axle from the right-hand side.

1. Locknut
2. Drive chain slack adjusting bolt

3. Axle nut

1. Locknut
2. Drive chain slack adjusting bolt

3. Wheel axle

4. Brake caliper bracket
5. Brake caliper

U4S811E0.book Page 41 Wednesday, August 8, 2007 1:14 PM

Summary of Contents for FZ-6 FZS6C













































































































Search results

Summary of Contents for FZ-6 FZS6C

Reviews:

Related manuals for FZ-6 FZS6C

Brands by name

Popular brands

Yamaha FZ-6 FZS6C, Owner'S Manual

Search results

Summary of Contents for FZ-6 FZS6C

Reviews:

Related manuals for FZ-6 FZS6C

Brands by name

Popular brands