Yamaha FZ-6 FZS6C Owner'S Manual Download Page 82

Page: 82 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-40

3. Remove the brake caliper (togeth-

er with the reflector) on each side
by removing the bolts.

CAUTION:

ECA11050

Do not apply the brake after the
brake calipers have been removed,
otherwise the brake pads will be
forced shut.

4. Pull the wheel axle out, and then

remove the wheel.

EAU43100

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Install the brake caliper (together

with the reflector) on each side by
installing the bolts.

NOTE:

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

4. Take the vehicle off the center-

stand so that the front wheel is on
the ground.

5. Tighten the wheel axle, the front

wheel axle pinch bolt and the
brake caliper bolts to the specified
torques.

6. Push down hard on the handlebar

several times to check for proper
fork operation.

EAU25080

Rear wheel

EAU25150

To remove the rear wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the axle nut.
2. Place the motorcycle on the cen-

terstand.

3. Remove the axle nut.
4. Loosen the locknut and drive chain

adjusting bolt on each side of the
swingarm.

1. Brake caliper
2. Brake caliper bolt

3. Reflector

Tightening torques:

Wheel axle:

72 Nm (7.2 m·kgf, 52 ft·lbf)

Front wheel axle pinch bolt:

19 Nm (1.9 m·kgf, 13 ft·lbf)

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lbf)

U4S811E0.book Page 40 Wednesday, August 8, 2007 1:14 PM

Summary of Contents for FZ-6 FZS6C













































































































Search results

Summary of Contents for FZ-6 FZS6C

Reviews:

Related manuals for FZ-6 FZS6C

Brands by name

Popular brands

Yamaha FZ-6 FZS6C, Owner'S Manual

Search results

Summary of Contents for FZ-6 FZS6C

Reviews:

Related manuals for FZ-6 FZS6C

Brands by name

Popular brands