manualshive.com logo in svg

Yamaha FX Cruiser WaveRunner 2007, Owner'S/Operator'S Manual, Page: 98 / 108

Share
Download
Yamaha FX Cruiser WaveRunner 2007 Owner'S/Operator'S Manual Download Page 98

Trouble recovery

93

gine. Any wrong connection could dam-
age the electrical system.

(4) Start the engine, and then disconnect the

jumper cables by reversing the steps
above.

CAUTION:

ECJ00690

●

Never push the start switch while the en-
gine is running.

●

Do not operate the start switch for more
than 5 seconds, otherwise the battery
will be discharged and the engine will
not start. Also, the starter motor could
be damaged. If the engine does not start
in 5 seconds, release the start switch,
wait 15 seconds, and then try again.

EJU34680

Replacing the fuses 

The fuses are located in the electrical box.
To replace a fuse:
(1) Remove the cap on the electrical box.

(2) Replace the blown fuse with the spare

fuse of the correct amperage by using the
fuse puller on the reverse side of the cap.

WARNING

EWJ00800

Do not use fuses of higher amperage than
recommended. Substitution with a fuse
that has an improper rating can cause ex-

1

Electrical box

2

Cap

3

Fuse

4

Spare fuse

1

Fuse puller

Fuse amperage:

Main fuse:

20 A

Meter fuse:

3 A

Bilge pump fuse:

3 A

UF1Y11E0.book  Page 93  Wednesday, August 23, 2006  11:43 AM

Summary of Contents for FX Cruiser WaveRunner 2007













































































































Reviews:

No comments