Yamaha FX Cruiser WaveRunner 2007 Owner'S/Operator'S Manual Download | Manualshive

Page: 88 / 108

background image

Maintenance and care

83

EJU34381

Cleaning and adjusting the spark
plugs

The spark plug is an important engine compo-
nent and is easy to inspect. The condition of
the spark plug can indicate something about
the condition of the engine. For example, if
one spark plug has a distinctly different color,
the engine could require servicing. Do not at-
tempt to diagnose any problems yourself.
Have a Yamaha dealer service the watercraft.
Remove and inspect the spark plugs periodi-
cally; heat and deposits will cause the spark
plugs to slowly break down and erode. If elec-
trode erosion becomes excessive, or if carbon
and other deposits are excessive, replace the
spark plug with the specified plug.

To remove a spark plug:
(1) Remove the air filter case cover and air

filter element. (See page 81 for air filter
element removal and installation proce-
dures.)

(2) Remove the spark plug cap.

CAUTION:

ECJ00210

Do not use any tools to remove or install
the spark plug cap, otherwise the ignition
coil coupler could be damaged. The spark
plug cap may be difficult to remove be-
cause the rubber seal on the end of the
cap fits tightly. To remove the spark plug
cap, simply twist it back and forth while
pulling it up; to install it, twist it back and
forth while pushing it down.

(3) Remove the spark plug.

Measure the spark plug gap with a wire
thickness gauge. Replace the spark plug

or adjust the gap to specification if neces-
sary.

To install a spark plug:
(1) Clean the gasket surface.
(2) Wipe any dirt from the threads of the

spark plug.

(3) Install the spark plug, and then tighten it

to the specified torque.

(4) Install the spark plug cap.

NOTE:

●

Wipe off any water on the spark plug or in-
side the spark plug cap before installing the
cap. Push the spark plug cap down until it is
securely installed.

●

If a torque wrench is not available when you
are installing a spark plug, a good estimate
of the correct torque is 1/4 turn to 1/2 turn
past finger tight using the spark plug
wrench included in the tool kit. Have the
spark plug adjusted to the correct torque
with a torque wrench as soon as possible.

Specified spark plug:

CR9EB

1

Spark plug gap

Spark plug gap:

0.7–0.8 mm (0.028–0.031 in)

Spark plug tightening torque:

12.5 Nm (9.2 ft-lb) (1.27 kgf-m)

UF1Y11E0.book Page 83 Wednesday, August 23, 2006 11:43 AM

«
...
86
87
88
89
90
...
»

Summary of Contents for FX Cruiser WaveRunner 2007













































































































Reviews:

No comments

Related manuals for FX Cruiser WaveRunner 2007

1992 270 Weekender

Brand: Sea Ray Pages: 21

Brand: Regal Pages: 352

Brand: Canadian Electric Boat Company Pages: 32

Brand: NW Explorations Pages: 59

Brand: Najad Pages: 44

Brand: UIM Pages: 17

Brand: Hallberg-Rassy Pages: 41

Brand: BENETEAU Pages: 30

GP1300R WaveRunner 2008

Brand: Yamaha Pages: 98

Brand: LaserPerformance Pages: 10

Inflatable Boats

Brand: West Marine Pages: 12

Brand: Sea Eagle Pages: 12

Brand: Sea Eagle Pages: 10

Moomba Kamberra

Brand: Skier's Choice Pages: 66

Moomba Craz 2019

Brand: Skier's Choice Pages: 111

Brand: Hyside Pages: 21

Brand: Bombard Pages: 9

SEA-DOO GTX RFI 5666 1998

Brand: BOMBARDIER Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands