Yamaha FX Cruiser WaveRunner 2007 Owner'S/Operator'S Manual Download Page 53

Page: 53 / 108

Operation

EJU31890

Engine oil

Use a combination of the recommended SAE
and API engine oil classifications shown in the
chart below.

CAUTION:

ECJ00280

Use only 4-stroke engine oil.

EJU31950

Filling the fuel tank

CAUTION:

ECJ00290

Be careful when refueling. Avoid getting
water and other contaminants in the fuel
tank. Contaminated fuel can cause poor
running and engine damage.

(1) Remove the seats. (See page 29 for seat

removal and installation procedures.)

(2) Remove the fuel tank filler cap, and then

slowly add fuel to the fuel tank. Stop filling
when the fuel level reaches approximate-

ly 50 mm (2 in) from the top of the fuel
tank as indicated in the illustration.

(3) Install the fuel tank filler cap and the

seats.

Approximately 50 mm (2 in) from top of the
fuel tank

Fuel tank capacity:

70 L (18.5 US gal) (15.4 Imp.gal)

UF1Y11E0.book Page 48 Wednesday, August 23, 2006 11:43 AM

Summary of Contents for FX Cruiser WaveRunner 2007













































































































Search results

Summary of Contents for FX Cruiser WaveRunner 2007

Reviews:

Yamaha FX Cruiser WaveRunner 2007, Owner'S/Operator'S Manual, Page: 53 / 108

Search results

Summary of Contents for FX Cruiser WaveRunner 2007

Reviews: