Yamaha F70AET Rigging Manual Download Page 223

Page: 223 / 329

6-9

FUEL TANK / GPS WIRE

Used to connect between a fuel tank level sensor and/or an MNEA0183 compatible GPS and the
speedometer (with fuel mgt gauge).

NETWORK HUB

Used to distribute the digital signal and electric power to the gauges and the other hubs.

Part No.

Remarks

6Y8-8356N-01

Twin fuel tanks acceptable

Ref. No.

Part name

Part No.

Remarks

Multi-hub

6Y8-81920-01

With ending resistor cap (P/N: 6Y8-85371-01)

Single hub (Inline hub)

6Y8-81920-11

Included ending resistor

2-pin sealing cap, RED

6Y8-82582-01

4-pin sealing cap, WHT

6Y8-82582-11

Same as bus wire cap of engine wire harness

300 (11.8)

220 (8.66)

GPS

P/B

Fuel
tank

(+)
(GND)

(BLK)

mm (in.)

178 (7.01)

Resistor cap (GRY)

194.8 (7.67)

7 (0.28)

41.4

(1.63)

21.4

(0.84)

(0.39)

22.55

(0.88)

19.65

(0.77)

42 (1.65)

(WHT)

26 (1.02)

18.54 (0.73)

19.3 (0.76)

(RED)

23.95 (0.94)

20.25 (0.79)

26 (1.02)

(WHT)

mm (in.)

* Face the connectors downward for installation.

Summary of Contents for F70AET










































































































































































































































































































































Search results

Summary of Contents for F70AET

Reviews:

Brands by name

Popular brands

Yamaha F70AET, Rigging Manual

Search results

Summary of Contents for F70AET

Reviews:

Brands by name

Popular brands