Yamaha F70AET Rigging Manual Download Page 174

Page: 174 / 329

5-10

SPEEDOMETER

SPEEDOMETER DIMENSIONS

* A 6 m (19 ft) water tube (P/N: 688-83557-00) is included in all speedometer units (except digital speedome-

ter unit P/N: 6Y5-83570-S6).

WATER PRESSURE DAMPER (OP)

Installing the water pressure damper between the gauge and water tube is recommended under fol-
lowing condition.

•

To reduce a risk if water has leaked at connector end causing the gauge damage.

•

The pointer of analog gauge is wiggled if water pressure pulsates.

93 (3.66)

11.2

(0.44)

(2.05)

41.9

(1.65)

84.5 (3.33)

97 (3.82)

8.5

(0.33)

65.5

(2.59)

210

(8.27)

25 (0.98)

W B

84.5 (3.33)

Digital

Analog

mm (in.)

Clamp

90465-11M10

Water Pressure Damper
6Y5-83728-00

Water Tube
6Y5-83557-31

Summary of Contents for F70AET










































































































































































































































































































































Search results

Summary of Contents for F70AET

Reviews:

Brands by name

Popular brands

Yamaha F70AET, Rigging Manual

Search results

Summary of Contents for F70AET

Reviews:

Brands by name

Popular brands