Yamaha F150G Page 55 Owner'S Manual Download

Page: 55 / 104

Operation

EMU40412

Outboard motor



Check that the outboard motor is mounted
properly and check the outboard motor
mounting bolts for looseness.



Check the propeller for damage.



Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out and
the engine can overheat during operation.

[ECM01802]

EMU40752

Installing top cowling

Check the rubber seal for damage. If the
rubber seal is damaged, have it replaced
by a Yamaha dealer.

Check that the rubber seal is seated all
the way around the bottom cowling.

Check that all of the cowling lock levers
are pulled outward.

Align the 3 protrusions on the top cowl-
ing with the corresponding holders on
the bottom cowling, and then place the
top cowling on the bottom cowling.

1. Oil dipstick
2. Upper mark
3. Lower mark

1. Fitting
2. Garden hose connector
3. Flushing device

ZMU07753

ZMU07754

1. Rubber seal
2. Bottom cowling

1. Top cowling
2. Protrusion
3. Holder
4. Bottom cowling

ZMU08836

ZMU07756

U6DV75E0.book Page 48 Tuesday, February 21, 2017 8:33 AM

Summary of Contents for F150G









































































































Search results

Summary of Contents for F150G

Reviews:

Related manuals for F150G

Brands by name

Popular brands

Yamaha F150G, Owner'S Manual

Search results

Summary of Contents for F150G

Reviews:

Related manuals for F150G

Brands by name

Popular brands