Yamaha F150G Page 41 Owner'S Manual Download

Page: 41 / 104

Instruments and indicators

Indicators

Yamaha Security System indicator (op-
tional)

This indicator appears, when the Yamaha Se-
curity System is in lock mode.

Make sure that the Yamaha Security System
indicator is off before starting the engine.

Engine trouble alert

If the engine malfunctions while cruising, the
pop-up window will appear.

To return to the normal display
Push the “SET” (set) button, and the engine
trouble-alert indicator will start to blink.

NOTICE

ECM00921

In such an event, the engine will not oper-
ate properly. Consult a Yamaha dealer im-
mediately.

Low battery voltage alert

If the battery voltage drops, the pop-up win-
dow will appear.

1. Yamaha Security System indicator (optional)
2. Engine trouble-alert indicator
3. Low battery voltage-alert indicator
4. Water separator-alert indicator
5. Low oil pressure-alert indicator
6. Overheat-alert indicator

1. Yamaha Security System indicator (optional)

ZMU08325

ZMU08326

1. Pop-up window

1. Engine trouble-alert indicator

ZMU08327

ZMU08332

U6DV75E0.book Page 34 Tuesday, February 21, 2017 8:33 AM

Summary of Contents for F150G









































































































Search results

Summary of Contents for F150G

Reviews:

Related manuals for F150G

Brands by name

Popular brands

Yamaha F150G, Owner'S Manual

Search results

Summary of Contents for F150G

Reviews:

Related manuals for F150G

Brands by name

Popular brands