Yamaha Electone STAGEA ELB-01, Owner'S Manual

Page: 54 / 188

ELB-01 Owner’s Manual 54
Voice Controls and Effects
3
ROTARY SPEAKER
This popular effect (used mainly for electronic organ
sounds) recreates the rich, animated pulsing sound of
a rotating speaker horn.
DISTORTION
This effect adds distortion to the sound.
WAH
This uses an automatic up/down filter sweep to
change the timbre of the sound, producing a “wah-
wah” sound.
Parameter Range Description
LFO Freq. 0.00 – 39.7 Hz Determines the tremolo speed.
AM Depth 0 – 127 Determines the amount of volume
change.
PM Depth 0 – 127 Determines the amount of pitch
change in the sound.
Input Mode Mono/Stereo Determines the input
configuration.
LFO Depth 0 – 127 Determines the depth of the
Tremolo effect.
L/R Depth 0 – 127 Determines the depth of panning
between the left and right
channels.
F/R Depth 0 – 127 Front/rear. Determines the depth
of the front and rear panning
effect. This controls both level
and pitch at the same time.
No. Type
08 AUTO PAN
09 XG AT PAN
10 EP AUTO PAN
Parameter Value Description
LFO Freq. 0.00 – 39.7 Hz Determines the frequency of the
Auto Pan effect, or how fast the
sound shifts between the left and
right channels.
L/R Depth 0 – 127 Determines the depth of the left/
right panning effect.
F/R Depth 0 – 127 Determines the depth of the front/
rear panning effect. This controls
both level and pitch at the same
time.
Pan L<->R
L->R
L<-R
Lturn
Rturn
L/R Determines the Auto Pan type.
(“L<->R” is a sine wave and “L/R”
is a sawtooth wave.)
No. Type
01 XG ROTARY SP
02 ROTARY SP 1
03 ROTARY SP 2
04 ROTARY SP 3
05 ROTARY SP 4
Parameter Value Description
EQ LowFreq. 32 – 2.0k Hz Determines the central frequency
of the low frequency range that is
boosted or cut.
EQ Low Gain -12 – +12 dB Determines the amount over
which the low frequency range is
boosted or cut.
EQ Hi.Freq. 500 – 16k Hz Determines the central frequency
of the high frequency range that
is boosted or cut.
EQ Hi.Gain -12 – +12 dB Determines the amount over
which the high frequency range is
boosted or cut.
No. Type
01 DIST HARD
02 DIST SOFT
03 OVERDRIVE
04 XG DIST
05 XG AMP SIM
Parameter Value Description
Drive 0 – 127 Determines the amount or degree
of distortion in the sound.
Amp. Type Off
Stack
Combo
Tube Determines the type of amplifier
that is simulated.
LPF Cutoff 1.0 – 18k Hz
Thru Determines the cutoff frequency
of the low pass filter. Frequencies
above this value are cut or filtered
out.
OutputLevel 0 – 127 Determines the level or volume of
the processed sound.
EQ Low Gain -12 – +12 dB Determines the amount of EQ
boost or cut in the low frequency
range.
EQ Mid.Gain -12 – +12 dB Determines the amount of EQ
boost or cut in the mid frequency
range.
Dry/Wet D63>W – D<W63 Determines the balance of the
original sound and the effect
sound.
No. Type
01 AUTO WAH
02 XG AUTO WAH
03 TOUCH WAH 1
04 TOUCH WAH 2
05 CLAVI TC WAH
06 EP TOUCH WAH
Parameter Value Description
LFO Freq. 0.00 – 39.7 Hz Determines the speed of the Wah
effect.
LFO Depth 0 – 127 Determines the depth of the Wah
effect.
Cutoff 0 – 127 Determines the central frequency
that the wah filter acts upon.
Resonance 1.0 – 12.0 Determines the frequency
bandwidth (around the central
frequency set in Cutoff above)
that the wah filter affects.
Parameter Value Description