Yamaha CZD250-A Owner'S Manual Download Page 102 | Manualshive

Page: 102 / 129

background image

Periodic maintenance and adjustment

9-21

9

EAU21963

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

z

The wheel rims should be
checked for cracks, bends, warp-
age or other damage before each
ride. If any damage is found, have
a Yamaha dealer replace the
wheel. Do not attempt even the
smallest repair to the wheel. A de-
formed or cracked wheel must be
replaced.

z

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

EAU50861

Checking the front and rear
brake lever free play

Front

Rear

There should be no free play at the
brake lever ends. If there is free play,
have a Yamaha dealer inspect the
brake system.

WARNING

EWA14212

A soft or spongy feeling in the brake
lever can indicate the presence of
air in the hydraulic system. If there is
air in the hydraulic system, have a
Yamaha dealer bleed the system be-
fore operating the vehicle. Air in the
hydraulic system will diminish the
braking performance, which may re-
sult in loss of control and an acci-
dent.

1. No brake lever free play

1. No brake lever free play

1

1

«
...
100
101
102
103
104
...
»

Summary of Contents for CZD250-A


































































































































Reviews:

No comments

Related manuals for CZD250-A

Brand: Free Spirits Pages: 32

Brand: KAYO MOTOR Pages: 84

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 88

Brand: Nolan Pages: 24

Brand: Dennis Kirk Pages: 5

RACE 13100CP520

Brand: Yoshimura Pages: 7

Brand: hepco & becker Pages: 4

MASTERFOX 125cc 2015

Brand: d'Magna Pages: 29

Brand: KTM Pages: 25

Brand: BMW Pages: 19

Brand: hepco & becker Pages: 2

BAR CLAMP MOUNT PRO

Brand: SP CONNECT Pages: 3

Brand: Yamaha Pages: 27

Brand: Yamaha Pages: 26

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 36

Brand: Yamaha Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands