Yamaha CS-R10, Systems Setup Manual

Page: 48 / 56

RIVAGE PM10 System Setup Guide
48
Analog Input Characteristics
*3*4*5
Analog output characteristics
*6*7*8
Digital I/O characteristics
Input Jack Gain
Input
Impedance
Source
Impedance
Input Level
Connector
Balanced /
Unbalanced
Sensitivity
*1
*1. Sensitivity is defined as the input level required to produce an output of +4 dBu (1.23 V) or the nominal output level when all faders
and level controls are set to maximum.
Rated Level
Max. Level
Before
Clipping
OMNI IN 1-8
+66 dB
10 kΩ
50-600Ω Mics
& 600Ω Lines
–82 dBu
(61.6μV) –62 dBu
(0.616 mV)
–42 dBu
(6.16 mV)
XLR-3-31 type
*2
*2. Connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*3. 0 dBu=0.775 Vrms for all specifications
*4. All AD converters are 24-bit linear.
*5. OMNI IN jacks 1-8 and the TALKBACK XLR jack f48 V DC phantom power, which is switchable for each jack individually from
the unit’s software.
Balanced
–6 dB
–10 dBu
(245 mV)
+10 dBu
(2.45 V)
+30 dBu
(24.5 V)
TALKBACK
+54 dB
10 kΩ
50-600Ω Mics
& 600Ω Lines
–70 dBu
(245 μV) –50 dBu
(2.45 mV)
–30 dBu
(24.5 mV)
XLR-3-31 type
*2
Balanced
–6 dB
–10 dBu
(245 mV)
+10 dBu
(2.45 V)
+30 dBu
(24.5 V)
Output Jack
Output
Impedance
Load
Impedance
Max Output
Level Select
Switch
*1*2
*1. The unit features an internal switch to change the maximum output level.
*2. The +24dBu switch position can be changed for fee so that the output level will be +20 dBu.
For more information, contact your Yamaha dealer.
Output Level
Connector
Balanced /
Unbalanced
Rated Level
Max. Level
Before
Clipping
OMNI OUT
1-8
75Ω 600Ω Lines
+24 dBu
(default)
+4 dBu
(1.23 V)
+24 dBu
(12.3 V)
XLR-3-32 type
*3
*3. Connectors are balanced. (1=GND, 2=HOT, 3=COLD)
Balanced +18 dBu
–2 dBu
(0.616 V)
+18 dBu
(6.16 V)
+15 dBu
–5 dBu
(0.436 V)
+15 dBu
(4.36 V)
PHONES
A, B (1/2
*8
)
15Ω
8Ω Phones — 75 mW
*4
*4. These measurements were obtained when the PHONES A/B LEVEL knobs are set 10 dB lower than the maximum.
150 mW
Stereo Phone Jack
(TRS)
*5
*5. Connectors are unbalanced. (Tip=LEFT, Ring=RIGHT, Sleeve=GND)
*6. 0 dBu=0.775 Vrms for all specifications
*7. All DA converters are 24-bit linear.
*8. PHONES A,B 1/2 (CS-R10), PHONES A,B (CS-R10-S)
Unbalanced
40Ω Phones — 65 mW
*4
150 mW
Jack Format Data Length Level Connector Balanced / Unbalanced
AES/EBU IN 1/2, 3/4, 5/6, 7/8
*1
*1. Features sampling rate converters.
• Input SRC
Supported input frequency (conversion source): 44.1 kHz-4%-200 ppm – 96 kHz+4.1667%+200 ppm
• Output SRC
Supported output frequency (conversion destination): 44.1 kHz-4%-200 ppm – 96 kHz+4.1667%+200 ppm
AES/EBU 24 bit RS422 XLR-3-31 type
*2
*2. Connectors are balanced. (1=GND, 2=HOT, 3=COLD)
Balanced
AES/EBU OUT 1/2, 3/4, 5/6, 7/8
*1
AES/EBU 24 bit RS422 XLR-3-32 type
*2
Balanced