Yamaha 2006 V Star XVS650AV Owner'S Manual Download Page 71

Page: 71 / 92

PERIODIC MAINTENANCE AND MINOR REPAIR

6-29

CAUTION:

ECA10640

Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.

3. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

EAU23780

Replacing the headlight bulb

This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.

1. Remove the headlight unit by re-

moving the screws.

2. Disconnect the headlight coupler,

and then remove the bulb cover.

3. Remove the headlight bulb holder

by turning it counterclockwise, and
then remove the defective bulb.

Specified fuses:

Main fuse:

30.0 A

Signaling system fuse:

10.0 A

Ignition fuse:

10.0 A

Headlight fuse:

15.0 A

Carburetor heater fuse:

15.0 A

Backup fuse:

XVS650A 10.0 A

Parking lighting fuse:

XVS650A 10.0 A

1. Screw

1. Headlight coupler
2. Headlight bulb cover

1. Headlight bulb holder

U3B720E0.book Page 29 Friday, April 15, 2005 1:34 PM

Summary of Contents for 2006 V Star XVS650AV





























































































Search results

Summary of Contents for 2006 V Star XVS650AV

Reviews:

Related manuals for 2006 V Star XVS650AV

Brands by name

Popular brands

Yamaha 2006 V Star XVS650AV, Owner'S Manual

Search results

Summary of Contents for 2006 V Star XVS650AV

Reviews:

Related manuals for 2006 V Star XVS650AV

Brands by name

Popular brands