Yamaha 2006 V Star XVS650AV Owner'S Manual Download Page 59 | Manualshive

Page: 59 / 92

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-17

6

EAU21940

Spoke wheels

To maximize the performance, durabil-
ity, and safe operation of your motor-
cycle, note the following points
regarding the specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage, and
the spokes for looseness or dam-
age before each ride. If any dam-
age is found, have a Yamaha
dealer replace the wheel. Do not
attempt even the smallest repair to
the wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU22041

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure XVS650 10.0–15.0 mm (0.39–
0.59 in)
XVS650A 5.0–10.0 mm (0.20–0.39 in)
as shown. Periodically check the clutch
lever free play and, if necessary, adjust
it as follows.

1. Loosen the locknut at the clutch le-

ver.

2. To increase the clutch lever free

play, turn the adjusting bolt in di-
rection (a). To decrease the clutch
lever free play, turn the adjusting
bolt in direction (b).

NOTE:

If the specified clutch lever free play
could be obtained as described above,
tighten the locknut and skip the rest of
the procedure, otherwise proceed as
follows.

3. Fully turn the adjusting bolt at the

clutch lever in direction (a) to loos-
en the clutch cable.

4. Loosen the locknut at the crank-

case.

1. Locknut

2. Clutch lever free play adjusting bolt
3. Clutch lever free play

1. Clutch lever free play adjusting nut (crank-

case)

2. Locknut

U3B720E0.book Page 17 Friday, April 15, 2005 1:34 PM

«
...
57
58
59
60
61
...
»

Summary of Contents for 2006 V Star XVS650AV





























































































Reviews:

No comments

Related manuals for 2006 V Star XVS650AV

Brand: Bajaj Auto Pages: 38

Brand: BMW Pages: 139

Brand: ESAB Pages: 4

Spyder ST Limited SE5

Brand: Can-Am Pages: 41

Brand: Shark Pages: 20

Brand: Power Fist Pages: 4

Brand: Benelli Pages: 582

Brand: Petzl Pages: 10

Brand: Tecno Globe Pages: 2

Slingshot R 2020

Brand: Polaris Pages: 173

Brand: Laverda Pages: 80

Brand: Zero Motorcycles Pages: 160

Brand: LAS Pages: 53

Brand: GAS GAS Pages: 80

Star XV19CTSZ 2009

Brand: Yamaha Pages: 104

SR125'99 3MW-AE3

Brand: Yamaha Pages: 25

Brand: Yamaha Pages: 220

Brand: Shark Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands