manualshive.com logo in svg

Yale SmartHome Alarm series, User Manual

Share
Download
Yale SmartHome Alarm series User Manual Download Page 6

  

Fault List

The fault list allows you to see/
delete a list of fault events. A fault 
event only appears if there is a fault 
event happening in your system.  
Upon selecting the option, you will 
be shown:

  

     start
       v

Scroll down to see a list of faults. To 
clear faults, press return key.

  

clear fault
  display? (ok?)

Press ok to clear fault. If the fault 
still persists on the system, the fault 
will immediately reappear on the list. 

Please contact your installer/
engineer to rectify the fault.

  

Hear Answer MC

Note: Only shown if the Answer 
Machine option is enabled and the 

control panel is connected to either 
the GSM/GPRS  or PSTN phone line.

When the caller leaves messages 
on the system, this option will be 
shown. Once selected, it will inform 
you if there are more than one 
recording (max. 20 voice messages).

  

 there are 02
     records

It will then proceed to playback 
all the messages starting from the 
oldest message. Message order and 
the time/date info will be displayed.

  

 play record 01
  11:33 may 12

You can stop the playback by 
pressing the Return key. The system 
will ask you if you want to delete All 
the voice messages. 

  

 do you erase
   the records?

Press the OK key to confirm deleting 
or press the Return key to go back 
to the main menu without deleting. 

User Menu

6

Summary of Contents for SmartHome Alarm series























Reviews:

No comments

Brands by name

Popular brands

Load more brands