manualshive.com logo in svg

Yale SmartHome Alarm series, User Manual

Share
Download
Yale SmartHome Alarm series User Manual Download Page 11

  

Daylight

This feature allows the user to 
define their local daylight saving 
hour

  

.disable
 start month
 end month

To enable, select the start Month

  

  start month
  mar     (OK)

Follow by selecting which Sunday it 
starts.

  

.first sunday
 second sunday
 third sunday
 last sunday

Select a start time and press ok 
when finished.

  

.midnight
 1 o'clock
 2 o'clock

Please now proceed to set the End 
month to complete the setting.

  

Bypass Sensors

As a one-time operation, the user 
can bypass any learnt sensor so 
that it is omitted from the system. 

Choose from a list of sensors to 
bypass

  

. PIR  Z01
  DC   z02
  dc   z03

  

 DC   z03
  bypass:  (OK?)

The selected device will now be 
marked with an “*”.

  

. PIR  Z01
  DC   z02
 *dc   z03

This is only valid when the user 
stays in the user menu and 
subsequently arm the system. When 
the user exits the user menu (Alarm 
Off), all bypass sensors is reset.

11

Summary of Contents for SmartHome Alarm series























Reviews:

No comments

Brands by name

Popular brands

Load more brands