Yaesu VXR-9000 Operating Manual Download Page 5

VXR-9000 FM R

EPEATER

 O

PERATING

 M

ANUAL

P

ROGRAMMABLE

 F

UNCTION

 

(

PF

)

 K

EY

 D

ETAILS

CH D

OWN

Press (or Press and hold in for one second) the 

PF

 key

assigned to “CH Down” to step to the next-lower oper-
ating channel.

CH U

P

Press (or Press and hold in for one second) the 

PF

 key

assigned to “CH Up” to step to the next-higher operat-
ing channel.

C

OMPANDER

Press (or Press and hold in for one second) the 

PF

 key

assigned to “Compander” to turn the Compander cir-
cuit “On” or “Off” (toggle). This function is only acti-
vated on the “Narrow Channel Spread” of the “

Base

Transceiver

” mode.

The Compander IC contains two variable gain circuits
configured for compressing and expanding the dynamic
range of the repeater’s transmitted and received audio
signal. When you enable this function, the signal-to-
noise ratio can be improved by reducing the transmit-
ted audio dynamic range.

CTCSS/DCS E

NC

Press (or Press and hold in for one second) the 

PF

 key

assigned to “CTCSS/DCS Enc” to turn the CTCSS/DCS
Encoder “On” or “Off” (toggle).

CTCSS/DCS D

EC

Press (or Press and hold in for one second) the 

PF

 key

assigned to “CTCSS/DCS Dec” to turn the CTCSS/DCS
Decoder “On” or “Off” (toggle).

CW ID

Press (or Press and hold in for one second) the 

PF

 key

assigned to “CW ID” to turn the CW Identifier feature
“On” or “Off” (toggle).

When the CW ID feature is set to “On,” your station’s
callsign will be superimposed on the outbound signal,
in Morse Code, at the beginning of every transmission.
Programming of the callsign is performed by your VER-
TEX STANDARD dealer.

3

F

UNCTION

CH D

OWN

CH U

P

C

OMPANDER

CTCSS/DCS E

NC

CTCSS/DCS D

EC

CW ID
T

WO

 T

ONE

 D

EC

CW ID S

IGNAL

CW M

ESSAGE

 1

CW M

ESSAGE

 2

CW M

ESSAGE

 3

CW M

ESSAGE

 4

CW M

ESSAGE

 5

CW M

ESSAGE

 6

CW M

ESSAGE

 7

CW M

ESSAGE

 8

DC P

OWER

 S

AVE

E

NCRYPTION

E

NCRYPTION

 C

ODE

K

EY

 L

OCK

L

OCAL

 PTT

M

ONITOR

M

ONITOR

 M

M

ULTI

 T

ONE

P

ANEL

 I

NDICATOR

R

EMOTE

R

EPEAT

R

ESET

S

CAN

S

QUELCH

T

EST

 T

ONE

T

EST

 T

ONE

 M

TOT
T

RANSMIT

TX P

OWER

 M

ID

TX P

OWER

 L

OW

PF-1  K

EY

P

RESS

P

RESS

 & H

OLD

PF-2  K

EY

P

RESS

P

RESS

 & H

OLD

PF-3  K

EY

P

RESS

P

RESS

 & H

OLD

PF-4  K

EY

P

RESS

P

RESS

 & H

OLD

PF-5  K

EY

P

RESS

P

RESS

 & H

OLD

PF-6  K

EY

P

RESS

P

RESS

 & H

OLD

Summary of Contents for VXR-9000

















Reviews: