Yaesu VX-8DR Page 39 Manual Download | Manualshive

Page: 39 / 176

background image

VX-8DR O

PERATING

M

ANUAL

37

DCS C

ODE

I

NVERSION

The DCS system was first introduced in the commercial LMR (Land Mobile Radio) ser-
vice, where it is now in widespread use. DCS is sometime referred to by its different
proprietary names, such as DPL

®

(Digital Private Line

®

, a registered trademark of Motorola,

Inc.).

DCS uses a codeword consisting of a 23-bit frame, transmitted (sub audible) at a data rate
of 134.4 bps (bit/sec). Occasionally, signal inversion can result in the complement of a
code being sent or received. This prevents the receiver’s squelch from opening with DCS
enabled, as the decoded bit sequence would not match that selected for operation.

Typical situations that might cause inversion to occur are:

Connection of an external receiver preamplifier.

Operating through a repeater.

Connection of an external linear amplifier.

Note that code inversion does not mean that any of the above listed equipment is defective!

In certain amplifier configurations, the output signal (phase) is inverted from the input. Small
signal or power amplifiers having an odd number (1, 3, 5, etc.) of amplification stages may
result in inversion of a transmitted or received DCS code. While under most circumstances
this should not occur (amplifier designs and industry standards take this into account), if you
find that your receiver squelch does not open when both you and the other station are using a
common DCS code, you or the other station (but not both) can try the following:

1.

Press and hold the

key for one second to enter the Set Mode.

2.

Rotate the

DIAL

knob to select Set Mode Item

27: DCS

INVERSION

.

3.

Press the

key briefly to enable adjustment of this Set

Mode Item.

4.

Rotate the

DIAL

knob to select one of the following modes:

RX-NORMAL, TX-NORMAL

:

Receive and transmit the Normal DCS Tone.

RX-INVERT, TX-NORMAL

:

Receive the Inverted DCS Tone and transmit the Normal DCS Tone.

RX-BOTH, TX-NORMAL

:

Receive both Normal and Inverted DCS Tones and transmit the Normal DCS
Tone.

RX-NORMAL, TX-INVERT

:

Receive the Normal DCS Tone and transmit the Inverted DCS Tone.

CTCSS/DCS/EPCS O

PERATION

DCS O

PERATION

«
...
37
38
39
40
41
...
»

Summary of Contents for VX-8DR

















































































































































































Reviews:

No comments

Related manuals for VX-8DR

Brand: Dish Network Pages: 18

Brand: Hallicrafters Pages: 8

Brand: Harman Kardon Pages: 10

Brand: Harman Kardon Pages: 2

Brand: Yaesu Pages: 4

Brand: Spektrum Pages: 19

Brand: Denon Pages: 218

Brand: Security Brands Pages: 3

Brand: Stabila Pages: 10

Brand: BluStream Pages: 4

Brand: Navilock Pages: 12

Brand: Harman Kardon Pages: 176

Brand: Comet Pages: 18

Brand: Intel Pages: 80

Brand: Galaxy Pages: 8

Brand: Motorola solutions Pages: 100

Brand: sebaKMT Pages: 46

Brand: Lectrosonics Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands