Yaesu VX-8DR Page 148 Manual Download

Page: 148 / 176

VX-8DR O

PERATING

ANUAL

146

ODE

TEM

26: DCS CODE

Function

: Setting of the DCS code.

Available Values

: 104 standard DCS codes.

Default

: DCS 023

ODE

TEM

27: DCS INVERSION

Function

: Enables/Disables the “Inverted”

DCS tone.

Available Values

: RX-NORMAL, TX-NOR-

MAL / RX-INVERT, TX-NORMAL /
RX-BOTH, TX-NORMAL / RX-NORMAL,
TX-INVERT / RX-INVERT, TX-INVERT /
RX-BOTH, TX-INVERT

Default

: RX-NORMAL, TX-NORMAL

RX-NORMAL, TX-NORMAL: Receive and transmit the Normal DCS Tone.
RX-INVERT, TX-NORMAL:

Receive the Inverted DCS Tone and transmit the Normal

DCS Tone.

RX-BOTH, TX-NORMAL:

Receive both Normal and Inverted DCS Tones and trans-
mit the Normal DCS Tone.

RX-NORMAL, TX-INVERT:

Receive the Normal DCS Tone and transmit the Inverted
DCS Tone.

RX-INVERT, TX-INVERT:

Receive and transmit the Inverted DCS Tone.

RX-BOTH, TX-INVERT:

Receive both Normal and Inverted DCS Tones and trans-
mit the Inverted DCS Tone.

ODE

TEM

28: DTMF DELAY

Function

: Selects the DTMF Autodialer Delay Time.

Available Values

: 50ms / 250ms / 450ms / 750ms / 1000ms

Default

: 450ms

ODE

TEM

29: DTMF MANUAL/AUTO

Function

: Enables/Disables the DTMF Autodial feature.

Available Values

: MANUAL / AUTO

Default

: MANUAL

ODE

TEM

30: DTMF SELECT

Function

: Programming of the DTMF Autodialer. See page 114 for details.

ODE

TEM

31: DTMF SPEED

Function

: Selects the DTMF Autodialer Sending Speed.

Available Values

: 50mS / 100mS

Default

: 50mS

ODE

ELECTION

ETAILS

DCS CODE

023 025 026 031 032 036 043 047 051 053

054 065 071 072 073 074 114 115 116 122

125 131 132 134 143 145 152 155 156 162

165 172 174 205 212 223 225 226 243 244

245 246 251 252 255 261 263 265 266 271

274 306 311 315 325 331 332 343 346 351

356 364 365 371 411 412 413 423 431 432

445 446 452 454 455 462 464 465 466 503

506 516 523 526 532 546 565 606 612 624

627 631 632 654 662 664 703 712 723 731

732 734 743 754

–

Summary of Contents for VX-8DR

















































































































































































Search results

Summary of Contents for VX-8DR

Reviews:

Related manuals for VX-8DR

Brands by name

Popular brands

Yaesu VX-8DR, Manual

Search results

Summary of Contents for VX-8DR

Reviews:

Related manuals for VX-8DR

Brands by name

Popular brands