Yaesu VX-8DR Page 156 Manual Download

Page: 156 / 176

VX-8DR O

PERATING

ANUAL

154

ODE

TEM

69: PASSWORD

Function

: Programming and activating the Password feature.

See page 122 for details.

ODE

TEM

70: PR FREQUENCY

Function

: Program the CTCSS Tone Frequency for the User Programmed Reverse CTCSS

Decoder.

Available Values

: 300 Hz ~ 3000 Hz (100 Hz/step)

Default

: 1600 Hz

ODE

TEM

71: PRI REVERT

Function

: Enables/Disables the Priority Revert feature.

Available Values

: ON / OFF

Default

: OFF

ODE

TEM

72: PRI TIME

Function

: Selects the time between the Priority (Dual Watch) channel checks, when the

feature is active.

Available Values

: 0.1sec ~ 0.9sec (0.1sec/step) or 1.0sec ~ 10.0sec (0.5sec/step)

Default

: 5.0sec

ODE

TEM

73: PTT DELAY

Function

: Selects the time delay before the carrier is transmitted, when the

PTT

switch is

pressed.

Available Values

: OFF / 20ms / 50ms / 100ms / 200ms

Default

: OFF

ODE

TEM

74: RPT ARS

Function

: Enables/Disables the Automatic Repeater Shift function.

Available Values

: ON / OFF

Default

: ON

ODE

TEM

75: RPT SHIFT

Function

: Sets the Repeater Shift Direction.

Available Values

: SIMPLEX / –RPT / +RPT

Default

: SIMPLEX

ODE

TEM

76: RPT SHIFT FREQ

Function

: Sets the magnitude of the Repeater Shift.

Available Values

: 0.000MHz ~ 150.000MHz (50 kHz/step)

Default

: Depends on the operating band and transceiver version.

ODE

ELECTION

ETAILS

Summary of Contents for VX-8DR

















































































































































































Search results

Summary of Contents for VX-8DR

Reviews:

Related manuals for VX-8DR

Brands by name

Popular brands

Yaesu VX-8DR, Manual

Search results

Summary of Contents for VX-8DR

Reviews:

Related manuals for VX-8DR

Brands by name

Popular brands