priority channels have been assigned, operation reverts
to the Scan Start Channel.
Last Busy
Lifting the microphone causes operation to revert to the
group and channel where activity was last detected. If no
activity was detected since turning on the radio, operation
reverts to the Scan Start Channel.
Voting scan
The radio can be programmed for Voting Scan, whereby
the radio will lock onto the strongest signal in a pre-
programmed set of channels. The radio is used as
normal, with the exception that transmission is not
allowed when the unit is out of range of the nearest
repeater. Consult your Yaesu dealer for more information
regarding this function.
Programmable Function Button
Low Power
With this feature enable, a button toggles between high
and low transmitter power, as programmed by the dealer.
MONI
This function is monitoring for the current channel.
SCN
This function is start and stop the scanning.
HA
Horn Alert function On and Off.
Call/Reset
When this feature is programmed and a selective call
has been received, momentarily press the button to reset
the flashing indicator and mute the receiver, otherwise
press the button to sent your radio’s identification code
(ANI) to the dispatcher.
Talk Around
The feature causes a button to select simplex operation
on semi-duplex channels: the transmit frequency
becomes the same as the receive frequency (regardless
of any programmed offset for the channel).
Note: This feature has no effect on simplex channels.
After pressing the button, ”TA” is displayed on LCD.
Encryption
When the Voice Scrambler feature is enabled, pressing
a button toggles the Scrambler on and off.
Alarm Function
When the “alarm” function is enabled, pressing a button
causes the radio to revert to a specially designated
channel, and causes the special “alarm” identifier code to
be transmitted automatically.
Note: This feature is only available as a “Secondary”
accessory to prevent accidental activation.
Fuse Replacement
If a fuse is blown, before replacing, see if you can
determine if it was caused by something outside of the
radio (perhaps a short circuit due to a worn cable or
pigtail near the radio). Contact your Ysesu dealer at once
if you do not find the cause. Replace fuses only with the
same type installed.
This is device complies with Part 15 of the FCC rules.
Operation is subject to the condition that this device does
not cause harmful interference.
Specifications
General
Frequency Range:
134-160MHz(VHF TYPE A)
148-174MHz(VHF TYPE C)
400-430MHz(UHF TYPE A)
450-480MHz(UHF TYPE D)
480-512MHz(UHF TYPE F)
Number of Channels & Spacing:
MAX 250 channels
25kHz,
12.5kHz
Modes of Emission:
16K0F3E, 11K0F3E
Frequency Stability:
2.5ppm(-30 to
+60°C)
Antenna Requirements: 50 ohms
Unbalanced (SO-239 socket)
Voltage Requirements:
13.8V ±15% DC
Negative ground
Current Consumption (approx.):
RX: 1.4A
TX: 12A(VHF 50W/UHF 60W)
Operating Temperature Range:
-30°C to 60°C (-22°F to 140°F)
Receiver
Receiver Circuit Type:
Double-Conversion
Superheterodine
Intermediate Frequencies:
43.95MHz, 450kHz
Sensitivity:
0.2µV 12dB SINAD (VHF)
0.25µV 12dB SINAD (UHF)s
Hum & Noise Ratio:
Better than 45 dB (25kHz/step)
Better than 40 dB (12.5kHz/step)
Adjacent Channel Selectivity:
>80dB (25-kHz/step VHF)
>78dB (25-kHz/step UHF)
>65dB (12.5-kHz/step)
Intermodulation Distortion:
Better than 78dB
Spurious Rejection:
Better than 85dB
Conducted Spurious Emission:
<-57dBm
Selectivity -6dB:
>12kHz
-60dB:
<30kHz
External Audio Output Power:
12 watts into 4 ohms
with < 5% THD
Transmitter
Output Power:
50watts(UHF)
40watts (UHF)
5watts (low programmable)
Modulation Type/Deviation:
Frequency Modulation
±5kHz(±2.5kHz)
Hum & Noise Ratio:
Better than 45 dB (25kHz/step)
Better than 40 dB (12.5kHz/step)
Modulation Distortion:
Less than 5% at 1kHz
Spurious Emission:
Better than 65dB(below carrier)
Microphone Impedance:
600ohms
Microphone Sensitivity:
-48dBm (3.0
mV)
Physical
Size (WHD,approx.):
178mm x 60mm x 195 mm
Weight (approx.):
2.2kg
Specifications subject to change without notice or obligation.
