background image

FT-65R/FT-65E Advance Manual

35

Set (Menu) Mode

Many 

FT-65R/E

 functions have already been described in previous chapters, 

The Set Mode Menu is used to configure the transceiver parameters, some of 

which have not been detailed previously. Use the following procedure to activate 

the Set Mode and configure the 

FT-65R/E

 function parameters:

1.  Press and hold the 

F

 key to enter the Set Mode.

2.  Press the [▲] or [▼] key to select the Set Mode Item to be adjusted.
3.  Press the 

key momentarily to enable adjustment of the Set Mode Item.

4.  Press the [▲] or [▼] key to adjust or select the parameter to be changed on the se-

lected Set Mode Item.

5.  After completing the selection and adjustment, press the 

PTT

 switch momentarily to 

save the new setting and exit to normal operation.

 Press and hold the 

F

 key to move from the lower menu contents to the upper 

menu in the Set Mode.

Item

(lower menu

item)

Function

Values

Default Value

1 APO

Setting of the Automatic Power-Off 

feature.

OFF / 0.5H to 12.0H (Step 

0.5H)

OFF

31

2 ARTS

Selects the Beep option and 

the Polling Interval during ARTS 

operation.

BEEP= INRANG / ALWAYS / 

OFF 

INTV= 25SEC / 15SEC

BEEP=OFF 

INTV= 25SEC

24

3 BATTSAVE

Selects the Receive-mode Battery 

Saver interval (“sleep” ratio).

200mS / 300mS / 500mS / 

1SEC / 2SEC / OFF

200mS

4 B-CH.L/O

Enables/disables the Busy Channel 

Lock-Out feature.

OFF / ON

OFF

32

5 BEEP

Beep function Enable/Disable on 

pressing the keypad, or stopping 

the receiver scanning.

KEY+SC

 :  The beeper sounds 

when any key is 

pressed, or when the 

scanner stops.

KEY 

:  The beeper sounds when 

any key is pressed.

OFF

 : Beeper is disabled.

KEY+SC / KEY / OFF

KEY+SC

6 BELL

Select the number of CTCSS/

DCS/PAGER/ARTS Bell ringer 

repetitions.

OFF / 1Time / 3Times/ 

5Times / 8Times / 

CONTINUE

OFF

10

7 COMPANDE

(COMPANDER)

Enables/disables the Voice 

Compander  feature.

OFF / ON

OFF

32

8 CTCSS

(CTCSS TONE)

Setting the CTCSS Frequency TX 

and RX.

50 CTCSS tones / OFF

TX=100.0Hz 

RX=100.0Hz

9

9 CW ID

CW Identifier during ARTS 

operation.

TX= OFF / ON 

ID= ------ (6 characters)

TX= OFF 

ID= blank

26

10 DC VOLT

displays Battery DC Voltage.  

5

11 DCS CODE

Setting the DCS CODE TX and RX. 104 DCS CODEs / OFF

TX=023 

RX=023

10

Summary of Contents for FT-65R








































Reviews: