Yaesu FT-2980E Operating Manual Download Page 69

Page: 69 / 80

10 CLK.SFT

Function

: Shifting of the CPU clock frequency.

Available Values

: ON / OFF

Default

: OFF

This function is only used to move a spurious response “birdie”, should it fall on a de-

sired frequency.

11 CW ID

Function

: Enables/Disables the CW identifier during ARTS Operation.

Available Values

: ON / OFF

Default

: OFF

12 CWTRNG

Function

: Enables/Disables the CW Training feature and selects the sending speed of

the Morse Code groups.

Available Values

: 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 15 / 17 / 20 / 24 / 30 / 40 WPM

/ OFF or 20 / 25 / 30 / 35 / 40 / 45 / 50 / 55 / 60 / 65 / 75 / 85 / 100 /

120 / 150 / 200 CPM

Default

: OFF

Note: To switch units between “WPM” and “CPM”, just press the [

MHz

(

SET

)] key.

13 DC VLT

Function

: Indicates the DC Supply Voltage.

14 DCS CD

Function

: Setting of the DCS code.

Available Values

: 104 standard DCS codes

Default

: 023

DCS CODE

023

025

026

031

032

036

043

047

051

053

054

065

071

072

073

074

114

115

116

122

125

131

132

134

143

145

152

155

156

162

165

172

174

205

212

223

225

226

243

244

245

246

251

252

255

261

263

265

266

271

274

306

311

315

325

331

332

343

346

351

356

364

365

371

411

412

413

423

431

432

445

446

452

454

455

462

464

465

466

503

506

516

523

526

532

546

565

606

612

624

627

631

632

654

662

664

703

712

723

731

732

734

743

754

15 DCS RV

Function

: Enables/Disables “Inverted” DCS code decoding.

Available Values

: ENABLE / DISABL

Default

: DISABL

16 DIMMER

Function

: Setting of the front panel display’s illumination level.

Available Values

: 0 (OFF) - 10

Default

: 5

“Set” (Menu) Mode

FT-2980R/E Operating Manual

Summary of Contents for FT-2980E

















































































Search results

Summary of Contents for FT-2980E

Reviews:

Related manuals for FT-2980E

Brands by name

Popular brands

Yaesu FT-2980E, Operating Manual

Search results

Summary of Contents for FT-2980E

Reviews:

Related manuals for FT-2980E

Brands by name

Popular brands