Yaesu FT-2600M Operating Manual Download Page 54

Page: 54 / 62

FT-2600M O

PERATING

ANUAL

06 CHNUM

Function

Enable/Disable the momentary display of the Memory Channel Num-
ber as the

Main Dial

knob is rotated.

Available Values

ON/OFF

Default Setting

OFF

07 CWID

Function

Enable/Disable the CW Identifier during ARTS operation.
The callsign also appears briefly when the radio is turned on.

Available Values

ON/OFF

Default Setting

OFF

08 CWIDN

Function

Program the callsign used by the ARTS CW Identifier.

Default Setting

YAESU

09 DC IN

Function

Indicate the Supply Voltage

10DCSN

Function

Setting of the DCS Code #.

Available Values

104 standard DCS codes.

Default Setting

023

11DCSNR

Function

Select “Normal” or “Inverted” DCS coding.

Available Values

TRX NOR

(Encoder: Normal Decoder: Normal)

RX REV

(Encoder: Normal Decoder: Inverted)

TX REV

(Encoder: Inverted Decoder: Normal)

TRX REV

(Encoder: Inverted Decoder: Inverted)

Default Setting

TRX NOR

(Encoder: Normal Decoder: Normal)

12 DIMR

Function

Setting of the front panel display’s illumination level.

Available Values

D1/D2/D3/D4/OFF

Default Setting

D1 (brightest setting)

13 DTMFD

Function

Setting of the DTMF Autodialer Delay Time

Available Values

50/250/450/750/1000 ms.

Default Setting

450 ms.

Menu System

Summary of Contents for FT-2600M































































Search results

Summary of Contents for FT-2600M

Reviews:

Related manuals for FT-2600M

Brands by name

Popular brands

Yaesu FT-2600M, Operating Manual

Search results

Summary of Contents for FT-2600M

Reviews:

Related manuals for FT-2600M

Brands by name

Popular brands