Yaesu FT-2600M Operating Manual Download Page 51

Page: 51 / 62

FT-2600M O

PERATING

ANUAL

Transceiver Cloning

You can transfer all data stored in one transceiver to another set by utilizing the handy
“C

LONING

” feature. This requires a user-constructed cloning cable which connects the

MIC

jacks on the two transceivers as shown below.

To clone from one transceiver to another, use the following procedure:
(1) Insert the Clone Cable into the

MIC

jack of each transceiver.

(2) Turn both transceivers off, then press and hold in the [

A/N

] key on each radio while

turning the power on again. The “

CLN

” notation will appear on the display.

(3) On the “destination” radio, press the [

D/MR

] button.

(4) Now, on the “source” radio, press the [

MHz

] key.

(5) If there is a problem during the cloning process, “

CLN ERR

” will be displayed. Check

your cable connections and try again.

(6) If cloning is successful, turn the “destination” radio off. Now turn the “source” radio

off.

Remove the clone cable. Channel and operating data for both radios are now identical.
They both may be turned on now for normal operation.

Summary of Contents for FT-2600M































































Search results

Summary of Contents for FT-2600M

Reviews:

Related manuals for FT-2600M

Brands by name

Popular brands

Yaesu FT-2600M, Operating Manual

Search results

Summary of Contents for FT-2600M

Reviews:

Related manuals for FT-2600M

Brands by name

Popular brands