pt - Tradução das instruções originais
148
Fonte de alimentação, monofásica
1x230Vac 50/60Hz
10
Número de bombas que podem ser
ligadas
10: Uma
20: Duas
15
Potência nominal do motor kW x 10
15=1.5kW x 10
D
Aplicação do software predefinido
D: águas residuais/elevação
B: grupo de pressão/pressurização
12A
Corrente máxima absorvida por uma
eletrobomba
3.3
Dados técnicos
Tab 1
Versão standard
Modelo do
quadro de
comando
Q-SMART 10
Q-SMART 20
Tensão nominal
de entrada (Uin)
1x230VAC (-15% a +10%)
Frequência de
entrada nominal
50/60 Hz
Corrente de
entrada nominal
1
(Uin=230V)
12A
24A
Proteção da
linha
recomendada
2
20A
40A
Corrente de
saída nominal
(Uin=230V)
12 A
2 x 12 A
Consumo em
standby
1.8W
(a potência em standby pode
variar conforme o tipo de sensor
ligado)
Tipo de carga
Motor elétrico
Cosø Nominal
≥ 0.6
Caixa
Auto-extinguível - Cinzenta
Proteção IP
frontal
55
Ligações (usar
exclusivamente
condutores de
cobre)
Réguas de terminais a parafuso
(fonte de alimentação, entrada e
saída)
Secção do cabo
de alimentação
máxima de
entrada
4 mm
2
Secção do cabo
de alimentação
máxima do
motor
4 mm
2
Set point
3
Pressão: 0 a 60 bar (0 a 6
MegaPa)
Nível: 0 a 50 m (0 a 164 pés)
Temperatura: -20 a 100°C (32 a
122°F)
Temperatura
ambiente
0 a 40°C (32 a 122°F)
Humidade
ambiente
10 a 90% sem condensação
Altitude
4
≤2000m s.n.m.
Alarme buzer
3.6kHz, Piezoelétrico
Fusível de
proteção do
motor F1, F2
12 A (gG)
CH10
10,3x38 mm
Fusível de
proteção auxiliar
F3
1A Desfasagem 5 x20 mm
(T1L 250V IEC60127-2/3)
Entradas digitais
5 entradas multifunções para
contacto NA/NF (sem tensão,
12V, 4mA )
Entradas
sondas elétricas
4 sensores elétrodos de nível,
1 elétrodo de referência
Sensibilidade: 5 a 100kOhm,
Capacidade das linhas: 10nF
máx,
Tensão de elétrodos: 6.5V -
20Hz
Entrada
analógica
Transdutor 0-20/4-20mA
(Entrada de sinal de valor ativo
para o sensor)
Entrada corrente 0-22 mA,
precisão 0.3%,
Alimentação 12 Vdc
Saídas digitais
1 Relé de
carga
2 Relés de
carga
30(15)A @ 250VAC
A corrente máxima permitida
para o motor elétrico é 12A
Porta Série TTL
Porta para comunicação com o
sistema de supervisão via TTL,
com protocolo de comunicação
Modbus
Sinais: +5V, RX, TX, RTS, 0V
Conector RJ45
Porta RJ45 para a comunicação
com o cartão com relés sem
tensão
Sinais: +12V - 120mA , 0V,
6 saídas por colector aberto
Dimensões e
Peso.
Consultar Figura
1. A corrente fornecida pelo quadro de comando
não deve ser inferior à corrente absorvida
pelas eletrobombas e também depende da
perda de tensão devida ao comprimento do
cabo.
2. Escolha a corrente do dispositivo de proteção
da linha em função da corrente máxima
absorvida pelos motores.
3. Só se for utilizado o sensor eletrónico.
4. Para altitudes mais elevadas ou outras
condições ambientais não abordadas neste
manual, queira por favor contactar o
Representante Pós-vendas / Assistência
local.
3.4
Especificações da bomba
Consultar o manual de utilização e manutenção da
eletrobomba. É essencial considerar as limitações
de uso do quadro de comando juntamente com as
da eletrobomba. Consultar os
Summary of Contents for Lowara Q-smart
