Xylem JABSCO Ballast SuperKing Quick Start Manual Download Page 2

2

SAFETY INFORMATION

WARNING! 

Prior to installation or use, read these 
installation and operating instructions. 
Installation and operation must comply 
with local regulations and accepted codes 
of good practice.

DO NOT USE PUMP WITH FLUIDS WITH A 
FLASH POINT BELOW 100°F (37.8°C) OR 
USE WHERE FLAMMABLE VAPORS ARE 
PRESENT.

This product has been designed for safe oper-
ation when used as detailed in accordance with 
the Manufacturer’s instructions.

Complies with USCG 183.410 and  ISO 8846 
Marine (Ignition Protection)

This manual also contains necessary informa-
tion for the correct installation. This manual was 
developed for qualified personnel with suitable 
training and/or technical qualification to operate 
this type of equipment.

NOTE:

 Failure to use this equipment in 

accordance with the manufacturer’s oper-
ating instructions may compromise your 
basic safety protection afforded by the 
equipment and may invalidate the warran-
ty / guarantee. The warranty / guarantee 
does not cover damaged caused by faulty 
installation or misuse of the equipment. If 
the recommended safety notices are not 
strictly observed, it can lead to serious or 
fatal injuries of personnel and/or material 
damage.

It is not recommended to run SuperKing 
pump dry.

Do not run the pump with a closed or 
restricted discharge line.

This pump is not a submersible pump.

Failure to observe the recommended 
safety procedures can lead to material 
damage.

Only qualified Service personnel should 
attempt to repair / service the product.

Do not operate the pump without
appropriate piping attached. 

Not to be used by children and
non-authorized personnel.

Please keep this manual available to all 
operators.

Always follow good working practice 
when using this pump.

Follow legislation applicable to your areas 
of operation. 

Do not touch the motor surface during or 
after operation of the pump as the surface 
can become hot.

Only use Original Equipment Manufacturer’s 
(OEM) parts and accessories. 

Do not use if damaged such as cut 
exposed wires.

Ballast SuperKing DC Flexible Impeller Pump

Caution, risk of danger.
See note  or adjacent symbol.

Caution hot surface 

Caution / risk of electric shock.

Recyclable packing material.

Do not dispose of product in normal domestic waste.

SYMBOLS IN THIS INSTRUCTION MANUAL AND PACKAGING

Summary of Contents for JABSCO Ballast SuperKing









Reviews: