3
0
10
20
30
40
50
60
70
80
GPM
0
0
10
10
0
20
30
m
3
/hr
5
10
40
METERS FEET
TOT
AL
D
YNAMIC HEAD
CAPACITY
MODEL: WEHT03xxM
SIZE: 2" Discharge
RPM: 1750
HP: .33 HP
SOLIDS:
3
/
4
" Diameter
15
5
5
15
25
35
WEHT03M
1 FT
2 GPM
Derate at
200ºF (93ºC)
68ºF (20ºC)
INTRODUCTION
Goulds Water Technology High Temperature 3885 Series
Effluent pumps are recommended for use in High Tem
-
perature applications up to 200ºF. The High Temperature
3885 Pump handles ¾” solids . Common applications in-
clude boiler blow down and High Temperature conden-
sate. Pump should be operated with a High Temperature
float switch sold separately.
SAFETY INSTRUCTIONS
TO AVOID SERIOUS OR FATAL PERSONAL INJURY
OR MAJOR PROPERTY DAMAGE, READ AND
FOLLOW ALL SAFETY INSTRUCTIONS IN MANUAL
AND ON PUMP.
THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT
AND MUST BE KEPT WITH THE PUMP.
This is a
SAFETY ALERT SYMBOL
.
When you see this symbol on the pump
or in the manual, look for one of the fol-
lowing signal words and be alert to the
potential for personal injury or property
damage.
Warns of hazards that
WILL
cause
serious personal injury, death or major
property damage.
Warns of hazards that
CAN
cause
serious personal injury, death or major
property damage.
Warns of hazards that
CAN
cause per-
sonal injury or property damage.
NOTICE: INDICATES SPECIAL INSTRUCTIONS
WHICH ARE VERY IMPORTANT AND
MUST BE FOLLOWED.
THOROUGHLY REVIEW ALL INSTRUCTIONS AND
WARNINGS PRIOR TO PERFORMING ANY WORK
ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.
This product can expose you to chemicals
including Lead, which is known to the
State of California to cause cancer and birth defects or
other reproductive harm. For more information go to:
www.P65Warnings.ca.gov.
All electrical work must be performed by
a qualified technician. Always follow the
National Electrical Code (NEC), or the Canadian Electri-
cal Code, as well as all local, state and provincial codes.
Code questions should be directed to your local electri-
cal inspector. Failure to follow electrical codes and OSHA
safety standards may result in personal injury or equip-
ment damage. Failure to follow manufacturer’s installa-
DANGER
WARNING
CAUTION
tion instructions may result in electrical shock, fire hazard,
personal injury or death, damaged equipment, provide
unsatisfactory performance, and may void manufacturer’s
warranty.
Standard units are not designed for use
in swimming pools, open bodies of water,
hazardous liquids, or where flammable gases exist. These
fluids and gases may be present in containment areas.
Tank or wetwell must be vented per local codes.
Only pumps specifically Listed for Class 1, Division 1 are
allowable in hazardous liquids and where flammable
gases may exist.
See specific pump catalog bulletins or
pump nameplate for all agency Listings
.
Disconnect and lockout electrical power
before installing or servicing any electrical
equipment. Many pumps are equipped with automatic
thermal overload protection which may allow an over-
heated pump to restart unexpectedly.
Do not use pump flammalde or explo
-
sive liquids. Pump is for water only.
PERFORMANCE
PRE-INSTALLATION CHECKS
Open all cartons and inspect for shipping damage.
Report any damage to your supplier or shipping carrier
immediately.
Important:
Always verify that the pump nameplate
Amps, Voltage, Phase and HP ratings match your control
panel and power supply.
This pump is oil-filled. If there are any signs of oil leak
-
age or if the unit has been stored for an extended period
check the oil level in the motor dome and the seal hous-
ing, if so equipped.
Check the motor cover oil level through the pipe plug on
top of the unit. The motor chamber oil should just cover
the motor. Do not overfill, leave room for expansion!
To check the seal housing oil level, where used, lay the
unit on its side with the fill plug at 12 o’clock. Remove the
WARNING
WARNING
WARNING
WARNING
MODELS
Order
Number
HP Phase Volts RPM Impeller
Dia. (In.)
Max.
Amps LRA
KVA
Code
Full Load
Motor Eff.
Resistance
Wt.
(Lbs.)
Cord
Length
Start Line-Line
WEHT0311M
0.33
1
115
1750
5.38
12.0
31.1
J
55
9.3
1.4
56
20'
WEHT0318M
208
7.3
19.5
K
51
9.1
4.2
WEHT0312M
230
6.1
16.5
J
54
11.7
5.6
*Add P1 to the end of the order number to include an ultra hi-temp float switch in the purchase.
Replacement part numbers for float:
A2HT31
– 115V and
A2HT32
– 208 and 230V (20' cord length).
WARNING
