background image

Installation Guide  

P. 15

 

Ignition-controlled Door Locks 

This feature will automatically lock all Doors as soon as the Key is turned to the 

IGNITION ON 

(RUN)

 position and the Brake Pedal is pressed. When the Ignition Key is turned to the 

OFF

 

position, the Doors will automatically unlock. 

Secure Lock 

This feature allows the Module to control certain OEM factory Alarm systems that use the 
factory Lock wire to 

arm 

the Alarm and the Unlock wire to 

disarm 

it. 

If Secure Lock is disabled (Option 1), the Module will still disarm before remote-starting the 
vehicle. If Secure Lock is enabled (Option 2), upon receiving a remote 

START

 signal the 

Module will 

UNLOCK

 the Doors (disarming the factory Alarm); 1/2 sec. after remote start it will 

re-lock 

the Doors. 4 seconds after shutdown, Secure Lock will 

re-lock 

all Doors once more 

(

arming 

the system again). 

Please note 

that most OEM systems will 

not 

rearm the Alarm 

while the Engine is running, but 

will 

lock the Doors. 

Turbo Mode 

This Option allows turbochargers to idle down: after the user leaves the vehicle, the Engine 
will keep running for 60 sec. and then shut down (It is a 1-minute Idle Mode). 

Safe Start (Child Safety Mode) 

Requires the user presses the 

START/STOP

 button on the Transmitter 

twice within 3 seconds

 

in order to start the vehicle.  

If the Special Safe Start Mode is selected (SWAP Start): 

1.

 

To start the vehicle, press the 

LOCK

 and 

UNLOCK

 

buttons simultaneously. 

2.

 

Pressing the 

START/STOP

 

button triggers 

AUX2

.

 

START/STOP 

button becomes 

AUX2 

trigger and the 

AUX2 

button becomes the 

START/STOP 

trigger

.

 

Table 7 

Passive or Active Arming of the Starter Kill 

The Starter Kill can be programmed to be 

active 

(

will not 

arm automatically) or 

passive 

(

will 

arm automatically). In Passive Mode, you can program it to arm automatically after 1 or 

3 min.  
To 

disarm 

the Starter Kill in Active or Passive Mode, the user must press and hold the 

UNLOCK

 button on the Transmitter (or enable Valet Mode). The Parking Lights will flash 

twice. If the Door Locks option was installed, this will also unlock the Doors.  
To 

arm 

the Starter Kill in Active or Passive Mode, the user must press and hold the 

LOCK

 

button on the Transmitter. The Parking Lights will flash once. (If the Door Locks option was 
installed, this will also lock the Doors). In Passive Mode, the system will automatically arm 
itself 1 or 3 minutes after the Engine is shut down. 

Lock Pulse Duration 

The Door Lock pulse duration can be programmed to give 7/10-sec. 

LOCK

 and 

UNLOCK

 

pulses (by default), 4-sec. 

LOCK

 and 

UNLOCK

 pulses, or for a 7/10-sec. 

LOCK

 pulse and two 

1/4 -second 

UNLOCK

 pulses (used for double-pulse disarm/unlock systems). 

Passive Or Active Arming 

The Starter Kill can be set to: 
1.

 

Option 1: 

PASSIVE Mode

: The Starter Kill will arm automatically after 60 seconds.  

Summary of Contents for EX-1724




















Reviews: