manualshive.com logo in svg

Xtreme Power Conversion NXTi 3P-3P, User & Installation Manual, Page: 21 / 36

Share
Download
Xtreme Power Conversion NXTi 3P-3P User & Installation Manual Download Page 21

Xtreme Power Conversion Corporation

NXTi 3P-3P User’s Manual

Page 21

Uninterruptible Power Supply

08: Bypass mode setting

Interface

Setting
Parameter 2:

OPN

: Bypass allowed. When selected, UPS will run at Bypass mode 

depending on bypass enabled/disabled setting.

FBD

: Bypass not allowed. When selected, it’s not allowed for run-

ning in Bypass mode under any situations.

Parameter 3:

ENA

:  Bypass  enabled.  When  selected,  Bypass  mode  is  activated. 

DIS

: Bypass disabled. When selected, automatic bypass is accept-

able, but manual bypass is not allowed. Manual bypass means us-

ers manually operate UPS for Bypass mode. For example, pressing 

OFF button in AC mode to turn into Bypass mode.

09: Battery backup time setting

Interface

Setting

Parameter 3:

000~999: 

Set the maximum discharge time from 0 min to 999 min. 

UPS will shut down to protect battery if the discharge time arrives 

before the battery is under voltage. The default value is 990 min.

DIS: Disable battery discharge protection and backup time will de-

pend on battery capacity.

10: Reserved

Interface

Setting

Reserve for future options.

11: Reserved

Interface

Setting

Reserve for future options.

Summary of Contents for NXTi 3P-3P





































Reviews:

No comments