manualshive.com logo in svg

Xtreme Power Conversion M90S 12kVA, Service Manual

Share
Download
Xtreme Power Conversion M90S 12kVA Service Manual Download Page 25

Xtreme Power Conversion Corporation

M90S Service Manual

Page 25

Uninterruptible Power Supply

LCD Message

Explanation

Solution

Warning 

0D:LineFuseOpen

Fuse is broken.

Turn off UPS and replace a good one with the bro

‐

ken one. If UPS fails again after you do this,  con

‐

tact  the  service personnel.

Warning 

0E:IICEepromFail

EEPROM operation error

Contact service personnel.

Warning 11:Bypas

‐

sIpNLoss

Neutral loss.

Check if the Neutral connection is well

and contact service personnel.

Warning 12:BpsPhas

‐

eError

Bypass phase error.

Check if the Bypass phase sequence is

correct and contact service personnel.

Warning 13:BpsVoltEr

‐

ror

Bypass voltage error.

Check  the  wiring  or  contact  service personnel

Warning 14:BpsPhase

‐

Fail

As stated.

Contact service personnel

Warning 15:OverLoad In line mode, the connected 

devices are demanding more 

power than the UPS can supply.

Reduce  some  load  and  check  output

Load-Capacity in specification.

Warning 16:OverLoad

‐

Lock

The connected devices are de

‐

manding more power than the 

UPS can supply. UPS will transfer 

to bypass mode from line mode.

Reduce  some  load  and  check  output

Load-Capacity in specification.

Warning 17:EpoActive Check the EPO connector.

Check if the connector is loose when EPO

acts abnormally.

Warning 18:Main

‐

tainOpen

The UPS is in maintenance 

mode.

Check if the 2-pin plate is not connected

to EMBS connector on the back panel of communi

‐

cation module when it acts abnormally.

Warning 19:LineDiff

Each module gets different line 

voltage when they are in parallel.

Contact service personnel.

Warning 1A:BypassDiff Each   module   gets   different   

bypass voltage when they are in 

parallel.

Contact service personnel.

Warning 

1B:InvCurUnbal

As stated.

Contact service personnel.

Warning 

1C:BpsUnstable

UPS switches between bypass 

mode and standby mode five 

times in 30 minutes due to ab

‐

normal utility.

Contact service personnel.

Warning 

1D:RedundancyFail

As stated.

Check if redundancy setting is correct or

not. Then, contact service personnel.

Warning! Battery Age 

Alert

Battery life is expired.

Check if the battery has been used over

its service age. Or contact service personnel.

Warning! Dry Contact 

Input Alarm 1

As stated.

Remove the node

Warning! Dry Contact 

Input Alarm 2

As stated.

Remove the node

Summary of Contents for M90S 12kVA






























Reviews:

No comments

Brands by name

Popular brands

Load more brands