manualshive.com logo in svg

Xtreme Power Conversion M90S 12kVA, Service Manual

Share
Download
Xtreme Power Conversion M90S 12kVA Service Manual Download Page 24

Xtreme Power Conversion Corporation

M90S Service Manual

Page 24

Uninterruptible Power Supply

LCD Message

Explanation

Solution

Fault 34:Ver Incompat The firmware version between 

UPS modules is incompatible.

Contact service personnel.

Fault 41:DSP Comm 

Fail

The internal communication in 

UPS module is interrupted.

Contact service personnel.

Fault 42:Over load

Heavy overload causes UPS fault. Reduce some load.

Fault 43:Charger Fail

Battery polarity is connected 

reversely or charger voltage is 

abnormal.

Contact service personnel.

Fault 44:Model Fault

UPS model is not able to identify.

Contact service personnel.

Fault 45:Mcu Comm 

Fail

As stated.

Contact service personnel.

Fault 46:CT Satiation

Load current sensor is abnormal.

Contact service personnel.

Fault 47:Fan Fault

The two fans are stuck or broken. Make sure fans work well when UPS is

working.

Warning 01:BatLow

Battery voltage is low.

Charge the battery when the mains is normal.

Warning 02:BatOpen

Battery is not connected.

1.  Check battery breaker status.

2.   Check if the battery connection is well con

‐

nected.

3.   Check the setting of Nominal Battery voltage.

4.   Contact service personnel if necessary

Warning 03:Bat

‐

PhaseLoss

The voltage between positive 

and negative battery is different.

Check the battery connection.

Warning 04:Lin

‐

eIpNLoss

Neutral loss

Check if the Neutral connection is well and contact 

service personnel.

Warning 05:LinePhas

‐

eError

As stated.

Check if the Mains phase sequence is

correct and contact service personnel.

Warning 06:LineVolt

‐

Error

As stated.

Check if the input wiring is correct or

contact service personnel

Warning 07:Line

‐

PhaseFail

As stated.

Check if the input wiring is correct or contact ser

‐

vice personnel

Warning 08:Over

‐

Charge

Battery voltage is too high.

Check  the  setting  of  Nominal  Battery

voltage and contact service personnel.

Warning 09:ChgFail

Battery voltage is detected as 

low level.

However, the charge is able to 

work.

Contact service personnel.

Warning 0A:OverTemp The temperature in UPS is higher 

than 75°C.  At  this  time,  the  

UPS  is  still running.

Check if the ambient temperature is over

specification.

Or contact service personnel.

Warning 

0B:PFCCurUnbal

PFC current is unbalance.

Contact service personnel

Warning 0C:FanError

Fan error.

Check if the fan is blocked or contact

service personnel.

Summary of Contents for M90S 12kVA






























Reviews:

No comments

Brands by name

Popular brands

Load more brands