Xtrails VESDA-E VEP-A00 Product Manual Download

Page: 51 / 109

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

4.5

Installation Checklist

Site Name

Address

Detector Serial Number(s) and Date of Manufacture

Name of Installer

Signature

Date

Perform the following checks listed below to ensure that all the necessary items are completed before handing
over to a commissioning engineer.

Installation Checks

Done (Y/N)

The detector is securely locked onto the mounting bracket (if in use). Refer to Figure 4-22
on page 27 for further information.

The sampling air pipes are firmly connected to the air inlet ports. Ensure that the pipes are
NOT glued.

The power supply wiring has been connected to the detector.

If required, the end of line resistor for the monitored GPI has been connected. Refer to
Section 4.3.11 on page 39 for further information.

The alarm and fault relay output terminals of the detector have been connected to the fire
panel.

The adhesive tape has been removed from the exhaust port. Ensure that the exhaust pipe
(if fitted) is NOT glued.

The protective film has been removed from the display.

The air sampling pipework has been installed and checked as per the site plans.

Summary of Contents for VESDA-E VEP-A00














































































































Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands

Xtrails VESDA-E VEP-A00, Product Manual

Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands