Xtrails VESDA-E VEP-A00 Product Manual Download

Page: 36 / 109

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

5. Insert the remaining three mounting screws (B) and tighten them (Figure 4-20).

Legend

Mounting bracket

Mounting screws

Figure 4-20: Mounting Bracket

6. Align the mounting studs (A) on the rear of the detector with the mounting stud slots on the mounting

bracket, and slide the detector down until the top of the detector is flush with the top of the mounting
bracket (Figure 4-21).

Legend

Mounting buttons

Figure 4-21: Mounting the detector

7. Open the door on the front of the detector (Figure 4-22). Refer to Section 7.2 on page 72 for further

information on how to open the door.

8. Insert and tighten the locking screw (A). This secures the detector to the mounting bracket.

Legend

Locking screw

Figure 4-22: Locking Screw

Summary of Contents for VESDA-E VEP-A00














































































































Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands

Xtrails VESDA-E VEP-A00, Product Manual

Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands