Xtrails VESDA-E VEP-A00 Product Manual Download | Manualshive

Page: 44 / 109

background image

VESDA-E VEP-A00-P Product Guide

36

www.xtralis.com

4.3.6

Relays

The relays, located on the main processor card, interface to the Fire Alarm Control Panel (FACP) to
communicate faults, alarms and disabled states. The relays can be programmed using Xtralis VSC. Relays 3
and 6 are permanently set for Urgent Fault and Fire 1 respectively. Table 4-22 below illustrates the default
assignments of functions (conditions) to relays and summarizes the default behavior of each relay. Section
5.5.9 describes how to configure the relay behavior using Xtralis VSC. It is possible to assign more than one
condition to a relay.

Fire 1 Relay

If a detector relay is to be used to signal fire alarm to the Fire Alarm Control Panel (FACP) then the Fire 1 relay
must be used.

Fault and Fire 1 Relay Terminals

The Urgent and Minor Fault relays are energized during normal operation while the Fire 1 relay is only
energized when a Fire 1 is detected. The operation of the relays are summarized in the following table.

Table 4-1: Typical Relay Operation

URGENT FAULT Relay

All Other Relays

No Fault

(Energized)

Fault

or unpowered state

No Fire

(De-energized)

Fire

Relay Assignments and Behaviour

l

Relays 1, 2, 4, 5 and 7 are fully configurable. For example, Relay 5 could be configured to de-energize on
Alert

l

Relays 3 and 6 are fixed to Urgent Fault and Fire 1 respectively. These relays may be assigned additional
conditions.

Relay #

Default

Assignment

Default to

Normally

Energized

Description for default configuration

Configurability

1

Disable

(Isolate) and

Standby

No

Energizes when an operator disables
(isolates) the detector. Also energizes when
the operator puts the detector into Standby
mode.

Fully

configurable

2

Minor Fault

Yes

De-energizes when a Minor Fault is
detected.

Fully

configurable

3

Urgent Fault,

Disable,

Standy

Yes

De-energizes when an Urgent Fault is
detected or when Disable or Standby
occurs.

Note that Relay 3 is fixed Normally
Energized in order to ensure that a fault will
be signaled when power to the VEP-A00 is
removed. See Table 4-1.

Urgent Fault

cannot be

removed. Other

conditions can

be added.

Fixed Normally

Energized

4

Alert

No

Energizes when the Alert alarm is initiated.

Fully

configurable

Table 4-2: Default Relay Assignments

«
...
42
43
44
45
46
...
»

Summary of Contents for VESDA-E VEP-A00














































































































Reviews:

No comments

Related manuals for VESDA-E VEP-A00

IntelliGuard 8000

Brand: Clifford Pages: 18

Tynetec Deaf Smoke ZXT487

Brand: LEGRAND Pages: 3

Brand: AcuRite Pages: 14

Brand: TFA Pages: 42

Brand: BRK electronic Pages: 2

Brand: Pit Boss Pages: 118

Brand: Trevi Pages: 9

Brand: Pandora Pages: 25

Music click clock

Brand: GINGKO Pages: 14

Virtual Key 2UK

Brand: Clifford Pages: 8

Brand: Clifford Pages: 9

Brand: Clifford Pages: 15

Brand: Clifford Pages: 13

Brand: Clifford Pages: 28

Brand: Alps Electric Pages: 13

Brand: Abus Pages: 63

Brand: Abus Pages: 72

Brand: Abus Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands