background image

7

safety

WARNING

Serious injury or death may occur from normal sparks in 

the multiple ignition sources or engine/burner exhaust.

Injury or death may occur as a result of improper fueling.

Serious injury or death may occur from a ground fire 

caused by a muffler spark.

Serious injury or death may occur if system safety’s are 

not properly maintained.

• Always operate pressure washer in a well ventilated area free of 

flammable vapors, combustible dust, gases or other combustible 

materials.

• Do not store the pressure washer near an open flame or any 

equipment such as a stove, furnace, water heater, etc., which utilizes 

a pilot light or sparking device.

• Do not use this pressure washer to spray flammable material!

• Do not smoke while filling burner fuel tank.

• Never fill the fuel tanks while the pressure washer is running or hot. 

Allow to cool two minutes before refueling.

• Always refuel slowly to avoid the possibility of spilled fuel which may 

cause a risk of fire.

• Do not refuel indoors or in a poorly ventilated area.

• Engine Fuel Tank: If using a Gasoline Engine, refuel with gasoline only. 

Do not use diesel or fuel oil.

• Burner Fuel Tank (Black): When refueling the Burner Fuel Tank, use 

No. 1 or No. 2 fuel oil/diesel or kerosene. Do not use gasoline.

• Do not operate the unit if gasoline or diesel fuel is spilled. Wipe the 

pressure washer clean and move it away from the spill. Avoid creating 

any ignition until the gasoline or diesel fuel has evaporated.

• A spark arrester must be added to the muffler of this engine if it is 

to be used on any forest covered, brush covered or grass covered 

unimproved land. The arrester must be maintained in effective working 

order by the operator. In the state of California, the above is required 

by law. (Section 4442 of the California Public Resources Code.) 

Other states may have similar laws. Federal laws apply on Federal 

lands.

• This pressure washer has a Safety Relief device which should never 

be altered, modified, removed or made inoperative. If the device fails, 

replace immediately with only genuine manufacturer replacement part.

Summary of Contents for X-HW2565AR



































Reviews: