XSHIFTER ELink Manual Download Page 10 | Manualshive

Page: 10 / 14

background image

Rev1

Page 10 of 14

Pod Set up

Customizing the Button Pods is
Not Released.

Pod Configuration

This configuration is valid for both
the front and rear derailleurs.

Cable Length main page

Use this to adjust the cable
tension.

Note that this will adjust the
individual gear settings
automatically.

Voice Main Page

Use your smart phone voice
recognition to adjust the ELink

«
...
8
9
10
11
12
...
»

Summary of Contents for ELink















Reviews:

No comments

Related manuals for ELink

Brand: Tailfin Pages: 4

Brand: Canon Pages: 16

Brand: Canon Pages: 48

Brand: Ranger design Pages: 6

Brand: Campbell Pages: 62

Brand: Campbell Pages: 26

Brand: CAMPAGNOLO Pages: 133

Brand: Campbell Pages: 34

Brand: CAMPARK Pages: 20

Brand: R.M. Young Pages: 4

Brand: Campbell Pages: 36

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: Vaillant Pages: 80

Brand: X10 Pages: 1

Brand: FORM FIT Pages: 2

Brand: Kodak Pages: 4

Brand: Ryobi Pages: 8

Brand: TALARIA Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands