Xray 2016 RX8, Instruction Manual

Page: 6 / 48

6
DETAIL
BAG
2. REAR SUSPENSION
44.5mm
NOTE
ORIENTATION
Tighten gently
Right thread
Left thread
2x
2x
2x
2x
Tighten composite hex nuts using
HUDY tool #107581
Follow the TECH TIP on page 41
to install the pivot balls
When you use INNER position on the upright, use SHORTER ball joint.
(INITIAL SETTING)
When you use OUTER position on the upright, use LONGER ball joint.
The length of the ball joint depends on the upright position. See page 7, step 3.
#345370
GRAPHITE REAR AERODYNAMIC DISC 1.6mm - SET
#345301
REAR CVD DRIVE SHAFT SET
HUDY SPRING STEEL™
902308
SH M3x8
902306
SH M3x6
901410
SB M4x10
901306
SB M3x6
345310
306219
901316
343311
342070
337250
372651
901410
342630
345360-O
901303
962121
941218
342070
941218
343285
902308
343150
901306
343130
337253
345280
902306
902308
343194
306219
343111
306219 COMPOSITE SET OF SERVO SHIMS (4)
337250 STEEL PIVOT BALL 8.4 MM (2)
337253 COMPOSITE ADJUSTING NUT M10x1 (4)
342070 COMPOSITE SET OF BUSHINGS (2)
342630 ADJ. TURNBUCKLE L/R 20 MM - HUDY SPRING STEEL™ (2)
343111 SUSPENSION ARM FOR EXTENSION - REAR LOWER
343130 COMPOSITE SUSPENSION ARM REAR UPPER
343150 UPPER BALL JOINT 5.8MM - SHORT & LONG (2+2)
343194 STEEL EXTENSION FOR SUSPENSION ARM - REAR LOWER (2)
343285 PIVOT BALL 6.8MM (2)
343311 COMPOSITE UPRIGHT REAR FOR AERO DISC
345280 WHEEL SPRING (2)
345310 REAR WHEEL AXLE - HUDY SPRING STEEL™
345360-O ALU REAR WHEEL LOCK - SWISS 7075 T6 - ORANGE (2)
345370 GRAPHITE REAR AERODYNAMIC DISC 1.6MM - SET (OPTION)
372651 PIVOT BALL UNIVERSAL 4.9 MM - HUDY SPRING STEEL™ (2)
941218 HIGH-SPEED BALL-BEARING 12x18x4 RUBBER SEALED (2)
901303 HEX SCREW SB M3x3 (10)
980322
962121
962120
901306 HEX SCREW SB M3x6 (10)
901316 HEX SCREW SB M3x16 (10)
901410 HEX SCREW SB M4x10 (10)
902306 HEX SCREW SH M3x6 (10)
902308 HEX SCREW SH M3x8 (10)
962120 WASHER S 12x15x0.5 (10)
962121 WASHER S 12x15x1.0 (10)
980322 PIN 3x22 (10)
02.1
3x8mm
3x6mm
3x6x1mm
COMPOSITE SHIMS
3x8mm
4x10mm
SUSPENSION ARMS
#343111 MEDIUM INCLUDED
#343112 HARD OPTION
#343113 GRAPHITE OPTION
SUSPENSION ARMS
#343111 MEDIUM INCLUDED
#343112 HARD OPTION
#343113 GRAPHITE OPTION
PIVOT BALLS
#337250 STEEL INCLUDED
#337251 ALU OPTION
#337255 TITAN OPTION
ADJUSTING NUT
#337253 COMPOSITE INCLUDED
#337252 ALU
OPTION
2.5mm 2.5mm
During initial assembly, tighten each
composite hex nut until the pivot ball
starts to bind, then loosen slightly. Verify
that the pivot balls move freely.
PIVOT BALLS MUST MOVE FREELY
DETAIL