background image

 

https://www.XPOtool.com 

 

Item 63371

 

Page 3 

 

The Tool Experts

 

 

  

 

06 2022-1

 

 

Introduction

 

 

Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to 
always take some basic safety precautions when using this product. Please read this operating manual 
carefully and make sure that you understand it.

 

Keep these operation instructions in a safe place.

 

 
 

Safety instructions

 

 

 

There  are  hazards  associated  with  the  use  of  a  jack.  To  avoid  the  risk  of  personal  injury  or 
property damage, make sure you fully understand the operating instructions for this product and 
the recommendations in the vehicle owner’s manual for jacking up your vehicle before lifting the 
vehicle.

 

 

Do not exceed the maximum load capacity of this jack.

 

 

This jack is intended for use in motor vehicles only.

 

 

Note  that  large  or  heavy  vehicles  may  exceed  the  specified  capacity  of  the  jack.  Check  the 
vehicle’s operating instructions or contact the vehicle manufacturer.

 

 

Do not use for any purpose other than lifting and lowering vehicles.

 

 

Never use to lift a structure or building.

 

 

Do not lift people, stand on the jack, or ride on it.

 

 
 

Assembling the handle

 

 

 

Insert  the  lower  handle  piece  into  the  middle  handle  piece  and  finally  into  the  upper  handle 
piece, making sure that the holes for the retaining clips line up.

 

 

Place the jack on the wheels on a flat surface and slide the assembled handle into the handle 
base.

 

 

Rotate until the square-shaped hole slides over the shaft in the handle base.

 

 

Double check that the handle is seated properly by finger pressure.

 

 

Loosen the handle 1/2 turn so it should rotate easily.

 

 

On the back of the jack, a large metal clamp holds the base of the handle flat against the jack. 
Hold the handle in a compressed position and carefully remove the clip by pulling it out. Release 
the pressure on the base of the handle.

 

 

 

Nr.

 

Descriptions

 

1

 

To operate the release valve

 

2

 

Close

 

3

 

Open

 

4

 

To  operate  the  jack,  insert  the 
handle end into the handle base 
and  pump  the  jack  handle  to  lift 
the load.

 

5

 

Load

 

 

 

 
 

 

 

 

 

 

Summary of Contents for 63371








Reviews: