background image

7

 

 

3)

 

The lift must be installed in level from front-to-back and side-to-side. 

4)

 

Make sure that the lift is level in all directions and weight should be shared 
equally by all four threaded mounting rods. 

5)

 

Bottom of the lift must be unobstructed after installation.  

 

3.

 

Installing on the Ceiling 

CAUTION:  

It is installer’s responsibility to make sure that the ceiling structure can 
support at least FOUR times the total weight of the lift and the projector. 
Reinforce the structure as required before installing the lift. 

 

1)

 

Please check that the ceiling has enough space to mount the lift. 

2)

 

 

No mounting material is provided.

 Please use suitable anchors and 

fasteners base on the ceiling type. 

3)

 

Mount two adjustable ceiling mounting bars to the ceiling. In case the ceiling 
has limited space, the installer has the option to mount the lift directly to the 
ceiling and threaded rod without using adjustable ceiling mounting bars.  

4)

 

Please refer the table below for mounting holes distances. 

 

 

A (mm) 

B (mm) 

C (mm) 

D (mm0 

XCU 190 

570 

680 

570 

495 

XCU 180 

530 

640 

530 

500 

 

Summary of Contents for XCU 190






















Reviews: