background image

2

Unpack your CA-1 or PA-1 and keep all packing materials for future transport or service, locate and remove all 
accessory items from the accessory box within the shipping carton.

Accessories Included:

Important Safety Instructions

Please  read  all  instructions  and  precautions  carefully  and  completely  before  operating  your  CA-1 
preamplifier and PA-1 mono block power amplifier.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings. 

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7.  Always keep this unit out of the reach of children.

8. Do not install this product near any heat sources such as radiators, heat registers, stoves, or other apparatus ( 
including   amplifiers) that produce heat.

9. Protect the power cord from being walked on or   pinched particularly at plugs, convenience receptacles, and the 
point where they exit from the apparatus.

10. Unplug this apparatus during lightning storms or  on  the  condition of  long-time non-using.

11. Always disconnect your entire system from the AC mains before connecting or disconnecting any cable, or when 
cleaning any component.

12.This product must be terminated with a three conductor AC mains power cord which includes an earth ground 
connection, to prevent it from shock hazard, all three connections must always be used.

13. AC extension cords are not recommended to use on  this product.

14. Never use flammable or combustible chemicals for cleaning audio components.

15. Never operate this product with any cover removed.

16. Never pour or spill liquids directly onto this unit.

17. Never block air flow through ventilation slots or heat sinks.

18.Keep the fuse out of short circuit.

19.Never take replacement of fuse uith non-specified values.

20.Never attempt to repair this product, if a problem occurs, contact your dealer.

21.Never expose this product to extremely high or low  temperatures.

22.Never operate this product in an explosive atmosphere.

Before Use

2. One piece of user manual (This manual)

1. One piece of AC power cord

S1

S2

S3

S4

Bal

Mute

F1

V

olume

-

+

R

E

M

O

T

E C

O

N

T

R

O

L

L

E

R

3. One piece of remote controller

Summary of Contents for CA-1













Reviews: