background image

 

 

xiMU - Technical Manual Version 2.10

 

 

15

 

 

3.1.5.

 

Optical path 

No additional filter glass. 

3.2.

 

xiMU USB2.0 specification  

3.2.1.

 

Sensor and camera parameters 

xiMU model 

MU9PC-MH 

MU9PM-MH 

Sensor parameter 

 

 

Brand 

Aptina, MT9P031I12STC 

Aptina MT9P031I12STM 

Color filter 

RGB Bayer mosaic 

None 

Type 

Rolling shutter, Global Reset Release 

Pixel Resolution (H × V)

 

[pixel] 

2592 × 1944

 

Active area size (H × V)

 

[mm] 

5.7 × 4.3

 

Sensor diagonal 

[mm] 

7.1 

Optical format 

[inch] 

1 / 2.5 (4:3) 

Pixel 

Size (H × V)

 

[µm]

 

2.2 x 2.2 

ADC resolution 

[bit] 

12 

FWC 

[ke-] 

4.9 

Dynamic range 

[dB] 

59 

SNR Max 

[dB] 

37 

Conversion gain 

[e-/LSB

12

0.82 

Dark noise 

[e-] 

DSNU 

[e-] 

0.92 

PRNU 

[%] 

Linearity 

[%] 

<0.2 

Camera parameters 

 

Digitization 

[bit] 

12 

Supported bit resolutions 

[pit/pixel] 

8, 10, 12 

Exposure time (EXP) 

20μs … 1

0sec 

Variable Gain Range (VGA) 

[dB] 

18 

Refresh rate (MRR) 

1

 

[fps] 

4.6 

Power consumption 

 

typical 

[W] 

0.76 

Maximum 

[W] 

0.9 

Idle 

[W] 

0.3 

Dimensions/Mass MU9Px-MH (with housing) 

 

Height 

×

 width 

×

 depth 

[mm] 

15 

×

 15 

×

 8.5 

mass 

[g] 

3.4 (without lens mount adapter) / 4.0 (with MECH-MU9-MH-ADAPT-M) / 

4.2 (with MECH-MU9-MH-ADAPT-L) 

Dimensions/Mass MU9Px-MBRD (board 
level) 

 

Height 

×

 width 

×

 depth 

[mm] 

14 

×

 13.2 

×

 3.7 (measured w/o connector) 

14 

×

 13.2 

×

 5.5 (measured with connector) 

mass 

[g] 

1.2 

table 3-3, MU9 sensor and camera parameters 

Notes: 

1) 

The figure indicates the maximum achievable frame rate for full frame readout. The real performance will be 
affected by USB controller, number and type of USB devices attached to this controller, system processor and 
memory speed and configuration. 

Summary of Contents for xiMU MU181CR-ON


































































































Reviews: