manualshive.com logo in svg

Xilinx ML630, User Manual

Share
Download
Xilinx ML630 User Manual Download Page 8

ML630 Board User Guide

www.xilinx.com

7

UG828 (v1.0) September 28, 2011

Chapter 1

ML630 Board Features and Operation

This chapter describes the components, features, and operation of the ML630 Virtex®-6 
HXT FPGA Optical Transmission Network (OTN) evaluation board. The ML630 board 
provides the hardware environment for characterizing and evaluating the GTX and GTH 
transceivers available on the Virtex -6 XC6VHX565T-2FFG1924C FPGA.

ML630 Board Features

•

Two Virtex-6 XC6VHX565T-2FFG1924C FPGAs

•

On-board power regulators for all necessary voltages with power status LEDs

•

All ML630 FPGA U1 and U2 I/O banks V

CCO

 voltage is 2.5V

•

Two types of external power supply jacks (12V “brick” DIN4 type, PC ATX type)

•

USB JTAG configuration port for use with USB A-to-Mini-B cable

•

System ACE™ controller with companion CompactFlash socket

•

General purpose pushbutton and DIP switches, LEDs, and test I/O header for each 
FPGA

•

VGA 2X5 male debug header for each FPGA

•

USB-to-UART bridge with USB Mini-B pcb connector for each FPGA

•

Two VITA 57.1 FMC HPC connectors

•

I

2

C bus hosting EEPROM, clock sources and FMC connectors

•

A separate SiTime fixed 200 MHz 2.5V LVDS oscillator wired to each FPGAs global 
clock inputs

•

Eight pairs of differential clock input SMA connectors

•

Six  I

2

C programmable Silicon Labs Si570 3.3V LVPECL 10 MHz to 810 MHz 

oscillators 

•

Two differential input 8X8 crosspoint switches providing 16 selectable differential 
clock sources

•

Four sets of plug and receptacle FCI Airmax 120 pin connectors implementing the 
Interlaken interconnect protocol

The ML630 board block diagram is shown in 

Figure 1-1

.

Caution!

The ML630 board can be damaged by electrostatic discharge (ESD). Follow 

standard ESD prevention measures when handling the board.

Summary of Contents for ML630



























Reviews:

No comments

Brands by name

Popular brands

Load more brands