manualshive.com logo in svg

Xilinx ML630, User Manual

Share
Download
Xilinx ML630 User Manual Download Page 24

ML630 Board User Guide

www.xilinx.com

23

UG828 (v1.0) September 28, 2011

Detailed Description

FPGA U2 User GPIO Header

Figure 1-2

 callout [28]

A standard 2 x 6, 100-mil pitch header (J103) brings out six FPGA I/Os for test purposes. 

Table 1-14

 lists these pins. J103 odd pin numbers are wired to GND (ground).

FPGA U2 USB to UART Bridge

Figure 1-2

 callout [29]

Communications between the ML630 board FPGA U2 and a host computer are 
accomplished through a USB cable connected to J106. Control is provided by U79, a USB to 
UART bridge (Silicon Laboratories CP2103). 

Table 1-15

 lists the pin assignments and 

signals for the USB connector J106.

The CP2103 supports an I/O voltage range of 2.5V on the ML630 board. The connections 
between FPGA U2 and CP2103 should use the LVCMOS25 I/O standard. UART IP (for 
example, Xilinx® XPS UART Lite) must be implemented in the FPGA logic. FPGA U2 
supports the USB to UART bridge using four signal pins:

•

Transmit  (TX)

•

Receive (RX)

•

Request to Send (RTS)

•

Clear to Send (CTS)

Connections of these signals between the FPGA and the CP2103 at U79 are listed in 

Table 1-16

.

Table 1-14:

FPGA U2 User GPIO Header J103 

FPGA U1 Pin

Net Name

J103 Pin

J35

U2_USER_IO_1

2

K35

U2_USER_IO_2

4

D35

U2_USER_IO_3

6

E35

U2_USER_IO_4

8

P35

U2_USER_IO_5

10

P34

U2_USER_IO_6

12

Table 1-15:

J106 USB Mini-B Connector Pin Assignments and Signals 

J106 Pin

Signal Name

Description

1

VBUS

+5V from host system

2

U2_USB_D_N

Bidirectional differential serial data (N-side)

3

U2_USB_D_P

Bidirectional differential serial data (P-side)

4

ID

Not  used8

Summary of Contents for ML630



























Reviews:

No comments

Brands by name

Popular brands

Load more brands