manualshive.com logo in svg

Xilinx KC705, User Manual

Share
Download
Xilinx KC705 User Manual Download Page 39

KC705 Evaluation Board

www.xilinx.com

39

UG810 (v1.3) May 10, 2013

Feature Descriptions

Details about the tri-mode Ethernet MAC core are provided in 

PG051

, 

LogiCORE IP 

Tri-Mode Ethernet MAC User Guide.

For more information about the Marvell 88E1111 see 

[Ref 4]

.

For more information about the ICS 844021-01 see 

[Ref 3]

.

USB-to-UART Bridge

[

Figure 1-2

, callout 

17

]

The KC705 board contains a Silicon Labs CP2103GM USB-to-UART bridge device (U12) 
which allows a connection to a host computer with a USB port. The USB cable is supplied 
in the Evaluation Kit (standard-A plug to host computer, mini-B plug to KC705 board 
connector J6). The CP2103GM is powered by the USB 5V provided by the host PC when the 
USB cable is plugged into the USB port on the KC705 board.

Xilinx UART IP is expected to be implemented in the FPGA fabric. The FPGA supports the 
USB-to-UART bridge using four signal pins: Transmit (TX), Receive (RX), Request to Send 
(RTS), and Clear to Send (CTS).

Silicon Labs provides royalty-free Virtual COM Port (VCP) drivers for the host computer. 
These drivers permit the CP2103GM USB-to-UART bridge to appear as a COM port to 
communications application software (for example, TeraTerm or HyperTerm) that runs on 
the host computer. The VCP device drivers must be installed on the host PC prior to 
establishing communications with the KC705 board.

Table 1-19

 shows the USB signal definitions at J6.

N29

PHY_TXER

F2

TXER

M27

PHY_TXCTL_T

XEN

E1

TXEN

N27

PHY_TXD0

F1

TXD0

N25

PHY_TXD1

G2

TXD1

M29

PHY_TXD2

G3

TXD2

L28

PHY_TXD3

H2

TXD3

J26

PHY_TXD4

H1

TXD4

K26

PHY_TXD5

H3

TXD5

L30

PHY_TXD6

J1

TXD6

J28

PHY_TXD7

J2

TXD7

J4

SGMII_TX_P

A3

SIN_P

J3

SGMII_TX_N

A4

SIN_N

H6

SGMII_RX_P

A7

SOUT_P

H5

SGMII_RX_N

A8

SOUT_N

Table 1-18: 

Ethernet PHY Connections 

(Cont’d)

FPGA Pin

(U1)

Schematic

Net Name

 M88E1111

(U37)

Pin Number

Pin Name

Summary of Contents for KC705



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands