xFusion Digital Technologies FusionServer 2288 V5 Manual Download Page 22

Page: 22 / 86

FusionServer 2288 V5 Server
Technical White Paper

5 Hardware Description

2022-11-11

Indicator

Description

⚫

Short-circuit protection

⚫

Device failure (excluding failure of all devices)

UID Indicator

The UID indicator helps identify and locate a device.

⚫

Off: The device is not being located.

⚫

Blinking or steady blue: The device is being located.

NOTE

You can turn on or off the UID indicator by pressing the UID button or
remotely running a command on the iBMC CLI.

Management network
port data transmission
status indicator

⚫

Off: No data is being transmitted.

⚫

Blinking yellow: Data is being transmitted.

Management network
port connection status
indicator

⚫

Off: The network port is not connected.

⚫

Steady green: The network port is properly connected.

5.2.3 Ports

Port Positions

Figure 5-12

Ports on the rear panel

VGA port

LOM port

Management network port

Serial port

USB 3.0 port

PSU socket

Port Description

Table 5-4

Description of ports on the rear panel

Port

Type

Quantity

Description

LOM port

1000BASE-
T

GE LOM service ports (electrical).

Summary of Contents for FusionServer 2288 V5























































































Search results

Summary of Contents for FusionServer 2288 V5

Reviews:

Related manuals for FusionServer 2288 V5

Brands by name

Popular brands

xFusion Digital Technologies FusionServer 2288 V5, Manual

Search results

Summary of Contents for FusionServer 2288 V5

Reviews:

Related manuals for FusionServer 2288 V5

Brands by name

Popular brands