Xerox Versant 3100 Press User Manual Download Page 145

Page: 145 / 170

Stock Properties > Advanced Stock Setup

Recommended
Incremental Ad-
justment

Available Range

Adjustment Step
Increments

Default Value

Option / Setting

Determined by
test print output

Available selec-
tions will be
based on the Pro-
files created by
the user

Distinct Selec-
tions Available

Default

Fold Adjustment
Profile

---

System Default
On
Off

Distinct Selec-
tions Available

System Default

Pre Gate Roll Ad-
justment

Paper Curl Correction

Follow recommen-
ded sequential or-
der:

Default
Type A
Type B
Type C

Distinct Selec-
tions Available

Default

1 Sided- Face Up

• Default

Custom

• Type A

Severe Upward
Medium Upward • Type B
Moderate Up-
ward

• Type C

• Custom Curl

Correction:

Slight Upward
No Curl

Slight (Very

Slight Downward

Small) Upward

Moderate Down-
ward

or Slight (Very
Small) Down-
ward

Medium Down-
ward

• Custom Curl

Correction:

Severe Downward

Moderate
(Small) Up-
ward or Moder-
ate (Small)
Downward

• Custom Curl

Correction:
Medium Up-
ward or Medi-
um Downward

• Custom Curl

Correction:
Severe (Large)
Upward or
Severe (Large)
Downward

7-27

Xerox

Versant

3100 Press

User Guide

Troubleshooting

Summary of Contents for Versant 3100 Press











































































































































































Search results

Summary of Contents for Versant 3100 Press

Reviews:

Xerox Versant 3100 Press, User Manual, Page: 145 / 170

Search results

Summary of Contents for Versant 3100 Press

Reviews: