Xerox Troy PocketPro 100 Operator'S Manual Download Page 33 | Manualshive

Page: 33 / 158

background image

Operator Guide

1- 17

Overview

Figure 1-11 Printer with inverter feeder/s feeder/s

bypass transport

Figure 1-12 Printer with inverter feeder/s feeder/s

feeder/s bypass transport

The illustrations above show a printer with two feeder/stacker
modules and a bypass transport, and a printer with three feeder/
stacker modules and a bypass transport. With the bypass
transport installed, the printer can support up to three feeder/
stacker modules, including the inverter feeder/stacker.

Paper stocks

supported on

bypass transport

The bypass transport accepts all paper stocks on which the printer
can print, and it accommodates simplex and duplex printing.

DFA support

The bypass transport meets the Xerox Document Feeding and
Finishing Architecture (DFA) specifications. The system software
supports DFA. However, in order for the bypass transport to
function correctly, you need to set up finishing personality profiles
to identify your finishing device to the printing system. (The
customer support representative for your finishing device can give
you the information you need to create a personality profile for
your third-party finishing device.)

Support and interface with feeders

For information on marketing partners that provide solutions for
support and interface with feeders, contact your local Xerox sales
representative.

«
...
31
32
33
34
35
...
»

Summary of Contents for Troy PocketPro 100































































































































































Reviews:

No comments

Related manuals for Troy PocketPro 100

Brand: IBM Pages: 112

Brand: ABLE Pages: 26

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

Brand: TASKalfa Pages: 36

X2650 - Color Printer 3-IN-1

Brand: Lexmark Pages: 2

Brand: SNBC Pages: 78

Line Printer VIII

Brand: Radio Shack Pages: 54

Brand: A&D Pages: 66

Accel a Writer 812

Brand: Xante Pages: 312

Brand: Oki Pages: 8

Brand: Microcom Pages: 73

Brand: SEWOO Pages: 12

Brand: Novexx Solutions Pages: 6

WorkCentre XD130DF

Brand: Xerox Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands