Xerox Synergix 8850 System Introduction Download Page 61

Page: 61 / 98

XES Synergix 8825/8830/8850/8855 & X2-TECH System Introduction

Printed Error Code

Description

What To Do About Printed Error Code

21C50D00

Address Field missing during Write command.

Call for Service.

21C50E00

Bad track found during Write command.

Call for Service.

21C50F00

Floppy Disk Controller reported equipment check during Write

Call for Service.

21C60100

No response from Floppy Disk Controller to Read Data command.

Call for Service.

21C60300

No results available from Floppy Disk Controller for Read command.

Call for Service.

21C60500

Wrong track found during Read command.

Call for Service.

21C60600

Floppy Disk Controller reported Read command was invalid.

Call for Service.

21C60700

Bad disk found during Read command.

Call for Service.

21C60800

Data FIFO overrun during Read command.

Call for Service.

21C60900

Sector not found on disk during Read command.

Call for Service.

21C60A00

Data CRC error detected during Read command.

Call for Service.

21C60B00

Address Field CRC error detected during Read command.

Call for Service.

21C60C00

Data Field missing during Read command.

Call for Service.

21C60D00

Address Field missing during Read command.

Call for Service.

21C60E00

Bad track found during Read command.

Call for Service.

21C60F00

Floppy Disk Controller reported equipment check during Read

Call for Service.

Summary of Contents for Synergix 8850



































































































Search results

Summary of Contents for Synergix 8850

Reviews:

Related manuals for Synergix 8850

Brands by name

Popular brands

Xerox Synergix 8850, System Introduction

Search results

Summary of Contents for Synergix 8850

Reviews:

Related manuals for Synergix 8850

Brands by name

Popular brands