background image

 

Service Guide

 

v

 

Contents

 

General Information

 1

 

The Phaser 1235 Color Printer  2

Printer RAM and printer capabilities  4
CRU life counter behavior  4

Print engine assemblies  5
The image processor board  11

The control panel  12

On Line LED  12
! Fault  12

Rear panel  13
Accessing special operating modes  14
System controller board LEDs  14
Paper tray type sensing  15

Specifications  16

Regulatory specifications  19

 

Error Codes and Messages

 21

 

Error messages  21

 

Troubleshooting

 31

 

Power on self-diagnostic test  32
Print engine troubleshooting  33

Testing the print engine  33
Verifying printer operation by using its self-test print  34
Verifying power supply operation  34

Measuring power supply voltages  34
Inspecting the low-voltage power supply fuse  36
Safety interlocks  36
Testing for a shorted motor  37

Motor and fuser roller resistances  38
Media jams and the paper path  39
Media-based problems  39

Media problems  39
Multiple-sheet pick  39
The media skews passing through the paper path  40
Paper tray indicates it is empty when it is not  40

Summary of Contents for 1235DT - Phaser Color Solid Ink Printer














Reviews: